BUILD AN ELECTRIC PADDLEBOARD THAT HITS 41 KM/H

Daniel Riley strapped two 6,000-watt motors under a paddleboard and hit 41 km/h on a lake — no hydrofoil, just prop thrust and spray.

by Daniel Riley

WorkshopEnergy

difficulty
●●●●●
time
several weekends
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is not a project you clone — it is a proof that twin high-power underwater motors can push a paddleboard to 41 km/h without a hydrofoil wing. Daniel Riley rebuilt his earlier efoil board, removed the wing, mounted two 6 kW motors with integrated ESCs underneath, 3D-printed the brackets, and tested propeller combinations until each motor pulled almost 5,900 watts at full throttle. The result sprays water everywhere and moves fast enough that he claims it is the world's fastest powered paddleboard, though he admits that record is his own assertion and 40 km/h is modest compared to boats. What makes this hard is not the concept — it is the fabrication without plans. You get no STL files, no wiring diagram, no battery pack specification, no motor model number, and no controller setup guide. You would be measuring frames from the video, guessing at structural reinforcement, sourcing motors by wattage and hoping they fit, and solving waterproofing, propeller efficiency and battery balancing on your own. The single biggest trap: buying motors without knowing whether their mounting geometry, shaft diameter and thrust curve will work for a SUP hull, then discovering they pull the board sideways or cavitate at speed. If you have done live electric watercraft before and treat this as inspiration rather than instruction, it is a compelling direction. If you need dimensions and a parts list, this will waste your month.

GOOD TO KNOW

  • —This is a video-documented one-off build, not a packaged project with files.
  • —No repository, no STLs, no wiring diagrams, no battery specs, no motor model numbers in the public domain.
  • —Riley reused parts from his earlier stabilized electric hydrofoil, but that project's files are also not published.
  • —The motor mounts were 3D printed and the propellers tested empirically — you would reverse-engineer both from the video.
  • —No safety documentation, no range figures, no battery chemistry or capacity stated.
  • —This is a pure maker exploration, shared as video only.

Parts to buy

6 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Two 6 kW motors with integrated ESCsFind
  • PropellersFind
  • High-capacity LiPo or Li-ion batteryFind
  • PaddleboardFind
  • Waterproof connectorsFind
  • Structural reinforcementFind

Can I build this?

PrintMotor mounts, reverse-engineered from video frames
BuyTwo 6 kW motors with integrated ESCs, propellers, high-capacity LiPo or Li-ion battery, paddleboard, waterproof connectors, structural reinforcement
Tools3D printer, hand tools, multimeter, access to open water, life vest, soldering iron, heat-shrink, possibly composite layup tools for hull reinforcement
SkillsHigh: electric propulsion system design, lithium battery management, waterproofing at high power, propeller selection, structural reinforcement of foam/composite hulls, balancing twin-motor thrust
TimeSeveral weekends — one to source and test-fit motors, one to design and print mounts, one to wire and waterproof, one to test propellers and tune, plus time lost to failures
Cost$$$ — two 6 kW motor units dominate, followed by battery pack and propellers; total cost not published
SafetyHigh-capacity lithium battery in a water environment, spinning propellers under the board, full-throttle instability on open water. Requires life vest, experience with electric boats, and a plan for battery disconnect and motor runaway. Not a first electric project.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Electric paddleboard build and lake test

Primary documentation of the build and test. No formal tutorial structure — this is Riley narrating his process and results.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video to understand motor placement, mount design and propeller testing approach (This is the only documentation)
  2. 2.Source two motors rated for continuous 6 kW with integrated speed controllers and underwater propeller mounts(Model not specified — you are matching specs to hull size and weight)
  3. 3.Design motor mounts that bolt to the paddleboard hull and survive thrust loads at full power(No CAD files available; reverse-engineer from video or design from first principles)
  4. 4.Plan battery pack for sustained dual-motor draw near 12 kW, with waterproof connectors and emergency disconnect(Capacity and chemistry not disclosed in the video)
  5. 5.Test on calm water with life vest and gradual throttle before attempting full-speed runs(Instability and spray increase sharply near top speed)

KNOWN ISSUES

  • No files means you are guessing motor mount geometry, bolt spacing, and hull attachment points from video frames — a mismatch wastes the first weekend and risks cracking the board.
  • Buying motors without knowing their propeller shaft size, mounting bolt pattern, or whether they produce balanced thrust will leave you with expensive hardware that does not fit or pulls sideways.
  • Battery pack sizing is not documented — underspec it and you get voltage sag at full throttle, overspec it and the weight drowns the hull or moves the center of mass wrong.
  • Waterproofing high-current connectors at 12 kW is harder than low-power RC boats — one leak at full power can start a lithium fire on water.
  • Twin-motor thrust balancing: if one motor spins faster or cavitates differently, the board veers hard at speed, and correcting it by leaning is nearly impossible.
  • No propeller specs given — wrong pitch or diameter and you get half the thrust or overheat the motors before hitting 20 km/h.

What motors and ESCs did he use?

Not specified in the video. He says they are 6 kW motors with built-in ESCs and measured close to 5,900 watts each at full throttle, but model numbers and suppliers are not disclosed.

How long does the battery last at full speed?

Not stated. At 12 kW combined draw, runtime depends entirely on battery capacity, which he does not share.

Is 41 km/h actually a world record?

Riley says 'if you believe Google' it is the fastest powered paddleboard, but he admits there is no official record and 40 km/h is slow compared to boats. Treat it as a personal claim, not verified.

Can I use this on a narrower board or kayak?

Possibly, but dual motors produce huge thrust and spray — a narrower hull might flip or submarine. The paddleboard's width provides stability he relies on.

What 3D printer settings for the motor mounts?

Not documented. You would need high infill, thick walls, and possibly reinforcement inserts to survive thrust loads and water impact.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Riley pulled almost 5,900 watts per motor at full throttle and hit 41 km/h without a hydrofoil — just raw prop thrust and a lot of spray. If you were building this, would you start with his dual-motor approach or try a single larger motor first to simplify balancing?

CompareeTEAM10d ago

Practical notes from our verification: this is a one-off video build with no repository, no STL files, no wiring diagram, and no battery specifications. The Instagram handle is @rctestflight_ and the YouTube video is the sole documentation. Riley explicitly says the 'world record' claim comes from a Google search, not an official body, and admits 40 km/h is modest compared to boats. The hardest part is not the concept — it is sourcing motors that fit a paddleboard hull when he never names the models, then designing mounts strong enough for 12 kW of thrust without cracking foam or fiberglass. If you have built electric boats before, this is a compelling direction; if you need a parts list and dimensions, you are reverse-engineering from video and it will take longer than the riding.

Daniel Riley

Riley runs the rctestflight YouTube channel, focused on electric aircraft, boats and experimental vehicles. This paddleboard build reused parts from his earlier stabilized electric hydrofoil project, removing the wing and repurposing the high-power motor setup for pure surface thrust.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.