TURN A DEAD WASHING MACHINE INTO A HYDRO POWER PLANT
A Fisher & Paykel Smart Drive motor, a Pelton wheel from eBay and the drop of a stream make about 600 W, enough with a battery bank to run a kettle, toaster and microwave off-grid.
by Angry Ram
- difficulty
- ●●●●○
- time
- several weekends
- license
- license not specified
- repo
- repo
●●●●○ · several weekends · license not specified · repo
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
Angry Ram turned the motor of a scrapped Fisher & Paykel Smart Drive washing machine into a water-powered generator for his off-grid house. With factory wiring the motor can make 400 volts AC, which is dangerous, so he rewires the stator (he covers that in a separate video on his channel). A Pelton wheel from eBay slides onto the shaft, the water jet has to hit the center of the Pelton cups, and a perspex window works as a service hatch. The height difference of a stream on his property gives about 45 PSI, and the generator makes about 21 amps at 29 volts, just over 600 watts, up to 900 with a bigger jet. A rectifier converts the three-phase AC to DC for a battery bank, an inverter boosts it to household voltage, and the battery bank covers loads above 600 watts, so he can run a kettle, toaster and microwave. A programmable logic controller dumps excess power into his hot water cylinder. This is for someone who already has a stream and is comfortable with high voltage. The video is a walkthrough, not a full guide: there is no parts list, no wiring diagram and no plans for the base. Water and electricity sit right next to each other here, so the electrics need a rain cover and proper protection. The most common trap is neglect: his old generator's hub melted because he did not check the bearings for about four months.
IN THE REPO
GOOD TO KNOW
- —This is a YouTube walkthrough from 2014, not a repository.
- —No CAD files, wiring diagrams, parts list or written guide.
- —Parts named in the video: a scrapped Fisher & Paykel Smart Drive (keep only the tub, stator, rotor, shaft and bearings), a Pelton wheel (under 100 USD on eBay at the time of filming), a rectifier, a fuse, a battery bank, an inverter, and a programmable logic controller to dump excess power into hot water.
- —The stator is rewired for battery charging; the rewiring is shown in a separate video on his channel, not in this one.
- —You need your own stream with enough height difference for water pressure; his is about 45 PSI.
- —No licence applies — this is documentation of a personal build, not a released design.
Parts to buy
11 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
Can I build this?
This build involves mains voltage — for adults comfortable with electrical work only.
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
Washing machine hydro generator walkthrough
2014 walkthrough by Angry Ram. Shows disassembly, what to keep, the Pelton wheel and nozzle, the perspex service hatch, the rectifier and the running numbers. The stator rewiring is in a separate video on his channel.
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Watch the 2014 YouTube walkthrough (Only guide available. Note the 400 V warning at 01:58 and the Pelton wheel and nozzle section at 03:19; the stator rewiring is in a separate video on his channel.)
- 2.Source a Fisher & Paykel Smart Drive washing machine for parts(Any size or model, they are all similar underneath. Whirlpool Cabrio and Maytag Bravos use the same type of stator. The rotor should turn freely with no side to side movement in the bearings. Keep only the tub, stator, rotor, shaft and bearings.)
- 3.Measure your stream's vertical drop and flow rate(The height difference between the water intake and the Pelton wheel creates the pressure; his is about 45 PSI. Less pressure makes less power.)
- 4.Get a Pelton wheel that fits the motor shaft(eBay had them for under 100 USD in 2014. His was adapted to slide onto the spline; you can also bolt one on using a thread on the shaft.)
KNOWN ISSUES
- Assuming any washing machine motor will work. The video covers the Fisher & Paykel Smart Drive (any size or model), and the description names Whirlpool Cabrio and Maytag Bravos as using the same type of stator. Check that the rotor turns freely and the bearings have no side to side movement.
- Skipping the rewiring video. The stator rewiring is shown in a separate video on his channel, not in this one, and there is no written wiring diagram.
- Underestimating the site. His 45 PSI comes from the height difference between the water intake and the Pelton wheel on a stream on his property. Less drop means less power, and no stream means no project.
- Skipping bearing checks. His old generator's hub melted after he did not check the bearings for about four months.
- Misaligning the water jet. The jet has to hit the center of the Pelton cups; he marks the nozzle position with a ruler, and the perspex service hatch lets you see what is going on inside.
- Ignoring the voltage risk. With factory wiring the motor can make 400 volts AC, which is dangerous, and here it runs next to water. Angry Ram does not recommend using it like that.
Can I use a different washing machine motor?
The video says the size or model of the Fisher & Paykel Smart Drive does not matter, they are all similar underneath. The video description adds that Whirlpool Cabrio and Maytag Bravos use the same type of stator motor. Other motors are not covered.
How much did the Pelton wheel cost?
Under 100 USD on eBay at the time of filming in 2014. His was adapted to slide straight onto the spline, but he says you can also bolt one on using a thread on the shaft.
What if my stream has less than 45 PSI?
You will make less power. His 600 watts come from about 45 PSI, giving 21 amps at 29 volts. The video does not give figures for lower pressure, so work out your own site before building.
Is there a wiring diagram for the stator rewiring?
Not in this video. Angry Ram says he made a separate detailed video on his channel showing how to rewire the stator. This video does not include a wiring diagram.
How often do the bearings need checking?
The video does not give an interval. His old generator's hub melted after he did not check the bearings for about four months, so check them regularly.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
A salvaged washing machine motor and a Pelton wheel that cost under 100 dollars make about 600 watts from a stream, and a battery bank covers the kettle and microwave. If you had a stream, what would you power first?
Angry Ram
Angry Ram has lived off the grid for a few years, powering his appliances, hot water and workshop tools himself. In this 2014 video he goes into more detail than his earlier short video on the same generator, which turned out to be popular.
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM25d ago
Practical notes from our verification: this is a 2014 YouTube walkthrough, not a repository or written guide. There is no parts list, no wiring diagram and no plans for the base; the stator rewiring is in a separate video on his channel. The first prerequisite is the stream itself: the pressure comes from the height difference between intake and wheel, his is about 45 PSI, so assess your site before you buy anything. The second is voltage: with factory wiring the motor can make 400 volts AC, which is dangerous, and here it sits next to water. The perspex service hatch lets you see whether the jet hits the center of the Pelton cups. And check the bearings regularly: his old generator's hub melted after about four months without checks.