TURN AN ELECTRIC CAR BATTERY INTO A GIANT HOME BATTERY

A 60 kWh BYD car pack plus a solar inverter becomes a giant home battery for £1,650 — four times the capacity of a Powerwall.

by Battery Man

EnergyHome

difficulty
●●●●●
time
a weekend-plus
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Battery Man took a 60 kWh BYD car battery with only 100 cycles on it, stood it upright, bolted a Solax 8 kW solar inverter to a frame on top, and wired it into his house. A small battery emulator board makes the inverter think it is talking to a normal home battery, and Home Assistant runs the charge cycles based on time and demand. When he forced a charge, it pulled 7,800 watts into the pack. The whole thing cost £1,650, delivered four times the capacity of a Tesla Powerwall, and the pack had only 6,000 kWh through it — barely used. The video is a walkthrough, not a build guide. There is no wiring diagram, no emulator board spec, no written instructions. You will need to pause and screenshot timestamps to work out what goes where. The pack runs at 450 V, weighs enough to need an engine crane, and ties into mains AC on the other side of the inverter. This is qualified-electrician territory. Smaller 20-40 kWh EV packs are easier to handle, but the principle is the same: buy a lightly-used car battery, add an inverter that speaks the right protocol, and connect a board that translates between the two. The one thing most likely to go wrong is the emulator board configuration — the video skips over that setup, and getting the inverter to recognise the pack without throwing faults is where most attempts stall.

GOOD TO KNOW

  • —This is a YouTube build walkthrough, not a repository.
  • —No bill of materials, wiring diagrams, or written step-by-step instructions.
  • —Battery emulator board and Home Assistant integration shown but not documented.
  • —The video shows the full installation, including fuses, isolators, and DC cabling.
  • —No licence applies — this is a documentation video, not a released design.
  • —Qualified electrician work: 450 V DC, 60 kWh lithium pack, solar inverter integration.

Parts to buy

7 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • 60 kWh BYD car battery (or similar EV pack)Find
  • Solax X3 8 kW solar inverterFind
  • Battery emulator board (model not specified in video)Find
  • DC fusesFind
  • IsolatorsFind
  • Heavy DC cableFind
  • Modbus dongle for Home AssistantFind

Can I build this?

Printnothing required — hardware build
Buy60 kWh BYD car battery (or similar EV pack), Solax X3 8 kW solar inverter, battery emulator board (model not specified in video), DC fuses, isolators, heavy DC cable, Modbus dongle for Home Assistant
Toolsengine crane or hoist, crimpers for heavy DC cable, multimeter, insulated tools rated for high voltage DC, Home Assistant installation
Skillsqualified electrician — 450 V DC, lithium pack safety, solar inverter installation, Home Assistant configuration, Modbus protocol
Timea weekend-plus once you have the parts — longer if the emulator board needs debugging
Cost$$$, dominated by the EV battery (£1,650 in the video) and the solar inverter
Safety450 V DC, 60 kWh lithium pack, mains AC integration. Engine crane required. Qualified electrician only. Smaller packs (20-40 kWh) reduce handling risk but voltage stays high.

This build involves mains voltage — for adults comfortable with electrical work only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

I Powered My House Using an EV Battery

Full build walkthrough including pack positioning, inverter mounting, fuses, isolators, emulator board connection, Home Assistant integration, and first charge test at 7,800 W.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the YouTube walkthrough (Pause at 0:00 (pack and inverter overview), 1:03 (fuses, isolators, connectors, Home Assistant dongle), 21:12 (Modbus connection), 22:37-22:58 (charge test), and 24:02 (pack specs and cost).)
  2. 2.Source a lightly-used EV battery pack(Look for 20-60 kWh packs with low cycle count. BYD, Nissan Leaf, and similar chemistry work. Check voltage: most run 350-450 V.)
  3. 3.Match a solar inverter that supports battery emulation(Solax X3 8 kW shown in the video. The inverter must support communication with home battery packs, usually via CAN or Modbus.)
  4. 4.Find or build a battery emulator board(The video does not name the board. Search for EV battery to solar inverter emulator projects — several open-source designs exist but configuration is not trivial.)

Resources

Documentation, files and community threads for this build — we link straight to the original sources and never rehost the creator’s files.

KNOWN ISSUES

  • The battery emulator board setup is not documented in the video, and getting the inverter to recognise the pack without faults is where most builds stall.
  • 450 V DC is not DIY voltage — one mistake and you are dead or the pack is on fire. Qualified electrician only.
  • The pack weighs hundreds of kilograms and needs an engine crane. Plan lifting and final placement before you buy.
  • No wiring diagram, no emulator pinout, no written steps — you will be pausing the video and reverse-engineering the connections.
  • Home Assistant Modbus integration is shown briefly but not configured on screen. Expect to spend time in forums working out the register map.
  • EV batteries can have internal BMS faults that only show under load. Test the pack with the seller present if possible.

Can I use any EV battery?

Most 350-450 V lithium packs will work in principle, but the emulator board needs to speak the right protocol to the inverter, and the BMS in the pack needs to be functional. BYD, Nissan Leaf, and BMW i3 packs are common choices.

Do I need solar panels to use this?

No. The inverter can charge from the grid and discharge to the house based on time-of-use tariffs. Solar input is optional.

What is the battery emulator board and where do I get one?

It translates between the EV battery BMS and the solar inverter so the inverter thinks it is talking to a home battery. The video does not name the board. Search for open-source EV battery emulator projects — several exist but expect configuration work.

Is 60 kWh overkill for a house?

Depends on your usage and goals. A typical UK home uses 8-10 kWh per day. 60 kWh gives you days of backup or lets you shift a week of grid usage to cheap overnight rates. Smaller 20-40 kWh packs are easier to handle and still dwarf a Powerwall.

What if the pack voltage does not match my inverter?

Most hybrid solar inverters accept 350-500 V battery input. Check your inverter datasheet. If the pack voltage is outside that range, you need a different inverter or a different pack.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

60 kWh for £1,650 is four Powerwalls worth of capacity at a tenth the price — but it runs at 450 V and needs an engine crane to move. Would you go for a smaller 20 kWh pack for easier handling, or is the capacity worth the complexity?

CompareeTEAM1d agoedited

Practical notes from our verification: the video is a walkthrough of a completed installation, not a step-by-step build guide. The battery emulator board is shown connected but never named or configured on screen, and there is no wiring diagram for the DC side. The Modbus dongle appears briefly at 21:12 but Home Assistant configuration is not shown. The charge test at 22:37 confirms the system works (7,800 W into the pack), and the pack specs at 24:02 confirm 60 kWh, 450 V, 6,000 kWh through it, 100 cycles, £1,650 paid. This is real, working, and cheaper than any commercial home battery at this capacity — but you are on your own for the emulator board setup and the wiring detail. Qualified electrician territory.

Battery Man

Battery Man runs a YouTube channel focused on EV battery repurposing, solar storage, and practical high-voltage builds.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.