TURN A DUMPSTER AIR CONDITIONER INTO GEOTHERMAL COOLING FOR YOUR HOME

A free window AC, 2,000 feet of buried pipe, and a water jacket turn yard soil into a heat sink that cools a house.

by Craftsman Chris

HomeEnergy

difficulty
●●●●●
time
several weekends
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Craftsman Chris pulled a 14,000 BTU LG dual inverter window AC from a dumpster, rotated its condenser without opening the refrigerant circuit, welded a water jacket around it, and pumps water through 2,000 feet of buried PEX to dump heat into the ground. A controller runs it from the thermostat and shuts it down if water hits 95°F. After weeks running, it delivers 26.5°F temperature split and about 54°F supply air to the main part of the house. This is for someone who wants to learn the approach and has serious fabrication and trenching capability — welding, refrigerant handling, digging four 500-foot trenches, and building a controller. The video shows the completed system and explains the logic, but you will have to reverse-engineer the water jacket, controller wiring, and pump sizing from what you see. The single biggest trap is underestimating the ground loop: 2,000 feet of buried pipe is a multi-day dig even with a trencher. Installed geothermal systems cost 20,000–40,000 dollars; this is the DIY version for someone who already has the tools and the weekend stamina. Cooling only, no heating mode.

GOOD TO KNOW

  • —This is a video walkthrough only, part 3 of a series.
  • —No repository, no wiring diagrams, no CAD, no BOM, no step-by-step written guide.
  • —The controller and water jacket fabrication are shown in the video.
  • —Burying the loops is covered in the earlier parts of the series.
  • —No stated licence. Educational content only.
  • —The builder says this is not laboratory-grade HVAC testing.

Parts to buy

6 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Window air conditionerFind
  • 000 ft of PEX tubingFind
  • Circulation pumpFind
  • Water jacket materialsFind
  • Controller with temperature sensorFind
  • Pipe fittingsFind

Can I build this?

Printnothing required
BuyWindow air conditioner, 2,000 ft of PEX tubing, circulation pump, water jacket materials, controller with temperature sensor, pipe fittings
ToolsWelder, tractor or trencher for the loops, multimeter, pipe cutter, basic hand tools
Skillswelding sheet metal, working around live refrigerant circuits, basic electronics for the controller, trenching and pipe laying, reading HVAC schematics from video only
Timeseveral weekends — trenching alone is multiple days, water jacket fabrication is a day, controller assembly and testing another day, integration and commissioning another weekend
CostNot stated in the video. The AC was free; PEX tubing, the pump and the controller make up most of the cost.
SafetyMains voltage on the AC unit and pump. Do not open the refrigerant circuit unless you are certified (venting refrigerant is illegal in many places); he rotated the condenser without opening it. Keep water away from electrical components. Call your utility locator before trenching.

This build involves mains voltage — for adults comfortable with electrical work only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Turning a Dumpster AC Into a Super-Efficient Geothermal Heat Pump

Part 3 of the series: the dumpster AC, water jacket, controller and performance after weeks of runtime. Earlier parts cover the buried loops.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the main video (Part 3 of the series. Shows the water jacket, controller, and final performance. You will need to reverse-engineer dimensions and wiring from what you see.)
  2. 2.Source a dual inverter window AC(His is an LG 14,000 BTU dual inverter unit he got from a dumpster for free.)
  3. 3.Plan the ground loop layout(He uses four 500 ft loops of PEX. Call your local utility locator (811 in the US) before digging.)
  4. 4.Fabricate the water jacket(Welded enclosure around the condenser coil. Must seal watertight and not restrict airflow or refrigerant lines.)
  5. 5.Build the controller(Relay driven by thermostat, temperature sensor on water jacket, cutoff at 95°F to prevent overheating.)
  6. 6.Install pump and plumbing(A pump circulates ground-loop water through the water jacket and back into the buried loops.)
  7. 7.Commission and test(Run for a few hours while monitoring water temp, supply air temp, and current draw. Check for leaks at every joint.)

KNOWN ISSUES

  • Burying 2,000 feet of pipe is the hardest part. Even with a trencher it is multiple days of work. Do not start until you have called 811 and marked utilities.
  • The video does not show wiring diagrams or controller code. You will reverse-engineer the relay logic and sensor wiring from the footage.
  • Opening the refrigerant circuit requires EPA 608 certification in the US. If you break a line, you must recover the refrigerant legally before repair.
  • The water jacket must seal well, since it sits next to the unit's electrical parts.
  • He uses four 500 ft PEX loops for this load in his yard; the video does not give sizing rules for other soils or units.
  • This cools only. There is no heating mode. If you want year-round conditioning, the design changes significantly.

Do I need to open the refrigerant circuit?

Not if you can rotate the condenser and evaporator without cutting lines, as shown in the video. If you do open it, you need EPA 608 certification (US) and refrigerant recovery equipment.

Can I use this in winter for heating?

Not as built. The video covers cooling only.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

After weeks running on its own, this system delivers a 26.5°F temperature split and about 54°F supply air — and the builder says it is not lab-grade testing. What would you monitor first to know if your ground loop is sized right?

CompareeTEAM1mo ago

The video shows the completed system running and the water jacket fabrication in detail, but the trenching and loop burial are in earlier parts of the series. The controller is shown but not fully documented, so you will be building it from what you see in the footage. The single biggest decision is whether you have the tools and the stamina for 2,000 feet of trenching — that is the wall most people will hit before the welding or the wiring.

Craftsman Chris

Craftsman Chris documents home HVAC and energy projects on YouTube. This geothermal cooling build is part 3 of a series showing the loop burial, water jacket fabrication, and controller integration.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.