TURN THE CHEAPEST MAC MINI INTO A 2TB ONE

DirectorFeng took a base 256GB M6 Mac mini, heated off the soldered original flash, and put new 2TB flash chips from the parts market in its place.

by DirectorFeng

Workshop

difficulty
●●●●●
time
Not stated by the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is not a beginner project — it is board-level microsoldering shown on video. DirectorFeng opens a base 256GB M6 Mac mini, takes out the logic board, heats off the original flash, cleans the pads, solders new 2TB flash chips (part numbers starting K8A9FJ1402) in their place and runs a flashing program from a MacBook. The Mac mini boots into macOS with 2TB, and in their own speed test read and write performance 'almost doubled'. Apple charges 1,000 dollars to go from 256GB to 2TB at purchase, which is more than the 899 dollar base model. But this route takes a BGA rework setup and serious microsoldering skill, it voids your warranty, the new flash comes from the parts market rather than from Apple, and one mistake can destroy the board. Worth watching to see what Apple's soldered storage means in practice; not something to try at home unless you already do board-level repair.

GOOD TO KNOW

  • —This is a YouTube video walkthrough, not a repository or written guide.
  • —There is no bill of materials — the video shows new flash chips with part numbers starting K8A9FJ1402, but not where they were bought.
  • —No schematic or pad map, and no written instructions for the flashing step shown at 14:20.
  • —The video has no voiceover; burned-in English subtitles explain the process, and the software UI on screen is in Chinese.
  • —There is no licence because there is no published design or code, just a demonstration.
  • —This upgrade voids your Apple warranty.

Parts to buy

3 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • New 2TB flash chips with part numbers starting K8A9FJ1402Find
  • From the parts marketFind
  • Video does not say where they were boughtFind

Can I build this?

Printnothing required
BuyNew 2TB flash chips with part numbers starting K8A9FJ1402 (shown on screen), from the parts market; the video does not say where they were bought. Apple does not supply them.
ToolsNot listed in the video. On screen: a suction cup to open the case, hot air to remove the original flash, BGA solder balls, and a MacBook running the flashing program.
SkillsProfessional microsoldering: BGA removal and soldering, pad cleaning, plus the flashing step shown at 14:20. If you have never desoldered a BGA chip, this is not the place to start.
TimeNot stated by the creator.
CostNot stated by the creator. For reference, Apple charges 1,000 dollars extra for 2TB over the 899 dollar 256GB base model.
SafetyHot air and molten solder: burn risk and risk of damaging the board. Opening the Mac and replacing the storage voids your warranty, and one mistake can destroy the logic board. Back up your data first — the original storage is removed.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Mac mini M6 storage upgrade (DirectorFeng)22:26

No voiceover; burned-in English subtitles explain the process. 3:20 opening the case. 4:25 the subtitles note the storage is now built in (it was a removable module on the M4). 8:20–13:40 the original flash comes off and the pads are cleaned. 13:40–15:00 the new K8A9FJ1402 chips; at 14:20 a MacBook runs the flashing program ('Start flashing'). 21:18 'Successfully upgraded to 2TB'. 21:40 their speed test: 'Read and write performance has almost doubled'.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the video through once without attempting anything (The video is a demonstration, not a tutorial. If the techniques look unfamiliar, do not proceed.)
  2. 2.Know which flash the video uses(The video shows new 2TB flash chips with part numbers starting K8A9FJ1402 but does not say where they were bought. They come from the parts market, not from Apple.)
  3. 3.Open the case and take out the logic board(Shown at 3:20–8:00 in the video: suction cup, bottom cover off, board out.)
  4. 4.Remove the original flash with hot air(Shown at 8:20–13:40. This is BGA microsoldering; if you have never done it, the board is very likely to be destroyed.)
  5. 5.Clean the pads and solder the new 2TB flash in place(Shown at 8:20–15:00. Damaged pads at this stage mean a dead board.)
  6. 6.Run the flashing step, reassemble and boot into macOS(At 14:20 a MacBook runs the flashing program ('Start flashing'); reassembly is at 16:00–20:20, and at 21:18 macOS shows 'Successfully upgraded to 2TB'. The video does not explain the flashing software.)

KNOWN ISSUES

  • The new flash chips come from the parts market, not from Apple. The video does not say where they were bought or how they hold up long-term.
  • Taking the original flash off with hot air and cleaning the pads is where the board can be destroyed. On a soldered Mac logic board there is no undo.
  • The speed result in the video is their own test. 'Read and write performance has almost doubled' is their claim, not an independent benchmark.
  • Opening the case and desoldering the storage voids your Apple warranty.
  • Hot air and molten solder can burn you and damage nearby components. Only attempt this if you already do board-level repair.

Can I do this with a soldering iron?

Not realistically. The flash chips are BGA parts with solder balls underneath, and the video uses hot air to take the original flash off. The exact tools are not listed in the video.

Where do I buy the replacement chip?

The video does not say. The new chips (part numbers starting K8A9FJ1402) come from the parts market, not from Apple, so their origin and availability are not guaranteed.

Will this work on the M4 Mac mini?

The M4 had its storage on a removable module, so it is a different job. This video is about the M6, where Apple soldered the storage back onto the main board.

Is the speed increase real?

The video shows their own speed test, where read and write performance 'almost doubled' compared with the original drive (which already read and wrote above 3000MB/s). It is not an independent benchmark, and we did not verify it.

Does Apple sell the chips?

The chips in the video are not from Apple; they come from the parts market. Apple's official option is picking more storage when you buy: 2TB costs 1,000 dollars more than the 256GB base model.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The video shows new K8A9FJ1402 flash chips going in, but not where they were bought — and the speed claim is from their own test. If you have upgraded soldered Mac storage before, where did your flash come from and how has it held up?

CompareeTEAM15d ago

Practical notes from our verification: the video has no voiceover — the steps are told through burned-in English subtitles, and the software on screen is in Chinese. The close-ups of the old flash coming off and the new chips going on are clear, but there is no schematic, no pad map and no explanation of the flashing software used at 14:20. The video does not say where the new flash chips were bought. The video title says 'Saved $1000!' — that is their claim; Apple does charge 1,000 dollars extra for 2TB over the 256GB base, but this route also needs the tools, the skill and the risk of a dead board. We did not verify the speed claim; it is their own test.

DirectorFeng

DirectorFeng is a YouTube creator who posts storage upgrades of Apple devices done at board level. In this video a base 256GB M6 Mac mini goes to 2TB. There is no voiceover — the process is told through burned-in English subtitles.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.