TURN TWO DEAD DVD DRIVES INTO A LASER ENGRAVER

The stepper motor carriages inside two old CD or DVD drives are enough to make the X and Y axes of a small laser engraver.

by Constantine (How To Do)

Workshop

Built withArduino

difficulty
●●●○○
time
Build time not stated by the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a genuine working laser engraver built around scrap parts. Constantine from How To Do took the stepper motor carriages out of two old CD or DVD drives, mounted one on an aluminium angle and the other on an acrylic base, and used them as the X and Y axes. Instead of the weak diode from a DVD-RW, he fitted a bought 1.5 watt 445 nm laser diode on a heatsink with a 50 mm fan. An Arduino Nano with two A4988 drivers and a 12 V supply runs it on GRBL 1.1 firmware, so it takes regular G-code or a picture. The drives give about 35 mm of travel, and it engraved a detailed tree into a block of wood. You watch the video and replicate what you see. The biggest limitation is the work area: about 3.5 by 3.5 cm. A commercial xTool F1 Lite sells for about 839 dollars and is much bigger and faster. A 1.5 W 445 nm laser can permanently damage your eyes, even from a reflection, so 445 nm laser safety glasses and smoke extraction are mandatory.

GOOD TO KNOW

  • —This is a video build, not a repository. There is no BOM, no STL files, no downloadable schematic, and no written instructions.
  • —GRBL 1.1 is open source firmware. The video shows downloading it and loading it onto the Arduino yourself.
  • —The laser diode, heatsink, fan, Arduino Nano, A4988 drivers and 12 V supply are bought parts. Only the carriages with their stepper motors come from the drives.
  • —The video shows the build process in detail but does not provide files or a parts list.
  • —No licence is stated.

Parts to buy

11 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Two dead CD or DVD drives with working stepper carriagesFind
  • 1.5 W 445 nm laser diode moduleFind
  • Heatsink and 50 mm fanFind
  • Arduino NanoFind
  • Two A4988 stepper driversFind
  • 12 V power supplyFind
  • Aluminium angleFind
  • Acrylic baseFind
  • 445 nm laser safety glassesFind
  • Smoke extractionFind
  • WiringFind

Can I build this?

PrintNothing required. The creator 3D printed a part to save time, but no print files are provided.
Buytwo dead CD or DVD drives with working stepper carriages, 1.5 W 445 nm laser diode module, heatsink and 50 mm fan, Arduino Nano, two A4988 stepper drivers, 12 V power supply, aluminium angle, acrylic base, 445 nm laser safety glasses, smoke extraction, wiring
Toolsscrewdriver to take the drives apart, soldering iron, multimeter to set the driver current, Arduino IDE to flash GRBL, G-code sender software
Skillsbasic electronics and soldering, setting stepper driver current with a multimeter, flashing Arduino firmware and changing GRBL settings, using G-code or laser engraving software. The build itself is straightforward if you can follow a video.
TimeNot stated in the video. The work is drive disassembly and mounting the carriages, building the frame, wiring the electronics, setting the driver current, then flashing and configuring GRBL before the first test burn.
Cost$$ — the drives are scrap; the bought 1.5 W laser module, Arduino Nano, drivers, 12 V supply and safety glasses make up the cost. The video gives no total.
SafetyThis is a Class 4 laser hazard. A 1.5 watt 445 nm blue laser can cause permanent eye damage if it enters your eye directly or off a reflection. Glasses rated for 445 nm are mandatory and must be worn by everyone in the room any time the laser is powered. Smoke extraction is mandatory too, because engraving produces smoke. Never point it at yourself or others, and never operate it around children or animals. There is also 12 V DC wiring, which is low voltage but can still short and cause burns or fires if miswired.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

DVD drive laser engraver build

The entire build is shown in this video. Key moments: drive disassembly and carriage extraction at 00:22, frame assembly at 00:44, laser module installation at 01:26, heatsink and fan at 01:46, Arduino and drivers at 02:51, GRBL firmware at 04:01, travel measurement at 07:12. No written instructions or files are provided.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video and note the parts shown (There is no written guide. You follow the video and replicate what you see.)
  2. 2.Source two dead CD or DVD drives with intact stepper carriages(The carriages with stepper motors become the X and Y axes. Travel is usually about 35 mm and depends on the drive.)
  3. 3.Buy a 1.5 W 445 nm laser diode module and proper safety glasses(The laser is bought, not taken from the drives. Get glasses rated for 445 nm before you ever power it on, and plan smoke extraction.)
  4. 4.Download and install GRBL 1.1 firmware on the Arduino Nano(GRBL is open source CNC firmware. You flash it using the Arduino IDE and then use a G-code sender to control the engraver.)

KNOWN ISSUES

  • Wearing glasses that are not rated for 445 nm. Check that the rating explicitly covers 445 nm and wear them whenever the laser is powered. A 1.5 W 445 nm beam can permanently damage your eyes, even from a reflection.
  • Underestimating the work area. It is only about 35 by 35 mm, so anything bigger will not fit.
  • Expecting every drive to behave the same. The travel depends on the drive, and in the video one stepper motor would not work at 1/16 microstepping, so it runs at 1/8.
  • Skipping the cooling. For longer jobs the 1.5 W diode needs to be cooled, which is why the build uses a heatsink with a 50 mm fan.
  • Not setting the A4988 current limit. The creator measured the voltage on the driver potentiometers: one motor ran too hot until he lowered it to about 130 mV, the other missed steps until he raised it to about 350 mV.
  • Running it without smoke extraction or in an open room with people or pets. Engraving makes smoke that must be extracted, and the beam can reflect off shiny surfaces. Everyone in the room needs 445 nm glasses.

Can I use the laser diode from inside the DVD drive instead of buying a new one?

The creator says the diode from a DVD-RW drive can work with a simple driver, but it is weak. For this build he fitted a bought 1.5 W 445 nm laser diode module instead, so the laser is not from the drives.

What is the actual engraving area?

About 35 by 35 mm. That is the travel the drive carriages allow, and the exact figure depends on the drive.

Do I need to buy anything else besides the parts shown?

Yes. Besides the drives you buy the 1.5 W 445 nm laser module, an Arduino Nano, two A4988 drivers, a 12 V supply, aluminium angle and acrylic, plus 445 nm laser safety glasses and a way to extract the smoke. The video shows the frame and mounts but does not give dimensions or a full parts list.

Can I cut acrylic or metal with this?

The video only shows engraving into wood. Cutting acrylic or metal is not shown, so do not count on it.

Is there a BOM or a list of links?

No. This is a video build with no written documentation. You source the parts yourself based on what is shown in the video.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The entire engraving area is 3.5 by 3.5 cm — smaller than a business card — but it engraved a detailed tree into wood. What would you engrave first if you built one?

CompareeTEAM23d ago

Practical notes from our verification: this is a video-only build with no repository, no STL files, and no BOM. The YouTube channel is How To Do, and the Instagram handle is @konsta.kogan. The video is clear and the build is genuine, but you are on your own for sourcing parts and replicating the frame. The single biggest safety note: a 1.5 watt 445 nm blue laser is a Class 4 hazard and can permanently damage your eyes, even from a reflection. Do not power it on without 445 nm safety glasses and smoke extraction.

Constantine (How To Do)

Constantine runs the How To Do YouTube channel. He says that for most of his projects it is easier and probably cheaper to buy the finished thing from China, and that he builds them for the process of making. This engraver reuses the stepper motor carriages from two old optical drives as its X and Y axes.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.