TURN AN OLD FRIDGE COMPRESSOR INTO A VACUUM CHAMBER

An old fridge compressor and a steel pot make a vacuum chamber that boils water at room temperature.

by Black Beard Projects

WorkshopScience

difficulty
●●●○○
time
Not stated by the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a practical workshop vacuum chamber for degassing resin, silicone, plaster and wax, and for stabilising wood. Black Beard Projects pulls minus 27.5 inches of mercury with his fridge compressor, enough to boil room-temperature water. The build is a 27 cm stainless steel pot with thick walls and a 10 mm high-strength polycarbonate lid, centre-punched, drilled and threaded for a 1/4 inch pipe thread connector, with half-inch fittings, a vacuum gauge and a ball valve (which turned out not to be needed). Thick-walled gas-rated tubing with steel hose clamps connects the compressor, car door rubber trim seals the rim, gaps in the seal were filled with silicone, and everything sits on a thick MDF base with a power switch for the compressor. The video description lists the materials with timestamps, but there are no drawings or exact dimensions beyond the 27 cm pot and the lid thickness. The first trap is refrigerant: every old fridge still holds refrigerant, and it must be recovered by a refrigeration service before you open the fridge or cut any lines. Never vent it into the air. The second trap is the lid: a thin or ordinary plastic lid can implode under vacuum, and the creator suggests about 20 mm for regular polycarbonate or plexiglass. The creator calls it very inexpensive if you can find the components used.

GOOD TO KNOW

  • —This is a YouTube video build, not a repository project.
  • —No CAD files, drawings or written instructions. The video description has a timestamped list of steps and materials.
  • —The build is shown in the video but dimensions and threading are not detailed.
  • —The creator suggests 10 mm high-strength polycarbonate or 20 mm regular polycarbonate for the lid.
  • —No licence is stated.
  • —Refrigerant must be recovered by a refrigeration service before you open any fridge. Never vent it into the air.

Parts to buy

12 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Fridge compressorFind
  • 27 cm stainless steel pot with thick wallsFind
  • 10 mm high-strength polycarbonateFind
  • 1/4 inch pipe thread connectorFind
  • 1/2 inch pipe fittingsFind
  • 1/4 inch female to 1/2 inch male adaptorFind
  • Vacuum gaugeFind
  • Ball valve (optional)Find
  • Thick-walled gas-rated tubingFind
  • Steel hose clampsFind
  • Teflon tapeFind
  • Car door rubber trimFind

Can I build this?

Printnothing required
Buyfridge compressor (from an old fridge, refrigerant recovered by a service first), 27 cm stainless steel pot with thick walls, 10 mm high-strength polycarbonate (or about 20 mm regular polycarbonate or plexiglass), 1/4 inch pipe thread connector, 1/2 inch pipe fittings, 1/4 inch female to 1/2 inch male adaptor, vacuum gauge, ball valve (optional), thick-walled gas-rated tubing, steel hose clamps, teflon tape, car door rubber trim, silicone, power switch, thick MDF board, rubber feet
Toolscentre punch, drill, tap for 1/4 inch pipe thread, wrenches, teflon tape, basic wiring tools for the power switch, tools to cut the MDF base
Skillscentre punching, drilling and threading the polycarbonate lid, assembling pipe fittings with teflon tape, sealing with rubber trim and silicone, wiring a mains power switch
TimeNot stated by the creator. The work covers drilling and threading the lid, assembling the fittings, sealing the rim, wiring a power switch and building the base.
Cost$$ - the creator calls it very inexpensive if you can find the components used; thick polycarbonate, fittings and a vacuum gauge cost more if bought new
SafetyRefrigerant first: an old fridge still contains refrigerant, and it must be recovered by a refrigeration service before you open the fridge or cut any lines. Never vent it into the air. Implosion: a thin or ordinary plastic lid can implode under vacuum; the creator used 10 mm high-strength polycarbonate and suggests about 20 mm for regular polycarbonate or plexiglass. Keep your face away from the lid while the chamber is under vacuum. Mains: the compressor runs on 230 V, and the power switch goes on a live wire; if you are not confident wiring mains, have someone qualified do it.

This build involves mains voltage — for adults comfortable with electrical work only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Fridge compressor vacuum chamber build

Shows the full build process. The video description has timestamps for each part: fridge compressor (0:03), steel pot (0:19), polycarbonate lid (0:21), tubing and hose clamps (0:32), drilling and threading (1:10-1:31), fittings and gauge (2:00-2:10), seal (4:12), silicone on seal gaps (5:00), power switch (5:50), MDF base (8:05), rubber feet (8:42). The description also states minus 27.5 inHg with this compressor and that the ball valve was not needed.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Have the refrigerant recovered from the old fridge by a refrigeration service before you open it(Never vent refrigerant into the air. Do not cut lines or open the system yourself.)
  2. 2.Watch the video and note the parts shown (The timestamps in the video description map to each part and step.)
  3. 3.Get a thick enough lid: 10 mm high-strength polycarbonate, or about 20 mm regular polycarbonate or plexiglass(This is the part most likely to be wrong — too thin and it will implode.)
  4. 4.Check the rim seal for leaks(The creator sealed the pot rim with car door rubber trim and filled the gap between the trim ends with silicone.)

KNOWN ISSUES

  • Using a lid that is too thin or the wrong plastic: a thin or ordinary plastic lid can implode under vacuum. The creator used 10 mm high-strength polycarbonate and suggests about 20 mm for regular polycarbonate or plexiglass.
  • Opening the fridge or cutting its lines before the refrigerant has been recovered. A refrigeration service must recover it first; never vent it into the air.
  • Assuming minus 27.5 inHg is guaranteed. That is the vacuum level with this particular compressor, and the video does not test others.
  • Not checking that the pipe connector threads match your fittings before drilling the lid.
  • Expecting drawings or exact dimensions. The video description lists the materials with timestamps, but the only sizes given are the 27 cm pot, the lid thickness and the 1/4 inch and 1/2 inch pipe threads.
  • Treating the power switch as an afterthought. The creator rewired the compressor's mains cable and put the switch on a live wire; if you are not confident wiring 230 V, have it done by someone who is.

Can I use any fridge compressor?

The creator used one fridge compressor and pulled minus 27.5 inches of mercury with it. That figure is for his compressor only; the video does not test other models. The old refrigerant must be recovered by a refrigeration service before you open the fridge or cut any lines. Never vent it into the air.

Can I use acrylic or regular plexiglass for the lid?

The creator used 10 mm high-strength polycarbonate and suggests going thicker, around 20 mm, for regular polycarbonate or plexiglass. A thin or ordinary plastic lid can implode under vacuum.

Do I need the ball valve?

With his compressor it turned out not to be needed: the compressor seems to have a one-way valve, so it does not let air back in even when switched off. That is his observation for his compressor, so check yours before leaving the valve out.

What can I use this for?

The creator built it for degassing resin, plaster, silicone and wax, and for stabilising wood. The vacuum level is what his compressor reached, minus 27.5 inHg, so treat it as a workshop tool.

Where is the written guide?

There is no written guide. The video description has a timestamped index of each step and material, from the compressor and pot to the seal, power switch and MDF base.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Minus 27.5 inches of mercury is enough to boil water at room temperature, and the creator says the compressor holds the vacuum on its own without the ball valve. What would you degass first?

CompareeTEAM23d ago

Practical notes from our verification: there is no written guide, only the video and a timestamped list of steps and materials in its description, so expect to pause and rewind. Before anything else, the old refrigerant has to be recovered by a refrigeration service; never vent it into the air. The lid is the part you cannot get wrong: the creator used 10 mm high-strength polycarbonate and suggests about 20 mm for regular polycarbonate or plexiglass, because a thin lid can implode. The minus 27.5 inHg reading is for his specific compressor, not a guarantee for all fridges. The creator calls it very inexpensive if you can find the parts used.

Black Beard Projects

Black Beard Projects built this vacuum chamber for degassing casting materials and stabilising wood. The Instagram account is @black_beard_projects.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.