TURN A 500 DOLLAR HAIR DRYER INTO A JET ENGINE
A Dyson Supersonic's compressor is smaller than a normal dryer's motor and blows twice as fast — Integza added a metal 3D printed combustion chamber and turned it into a tiny jet engine that melted his anemometer and scorched his tripod.
by Integza (Joel)
- difficulty
- ●●●●●
- time
- a weekend-plus (excluding metal print lead time)
- license
- license not specified
- repo
- repo
●●●●● · a weekend-plus (excluding metal print lead time) · license not specified · repo
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
This is not a project you can replicate from a repository — it is a documented experiment showing what happens when you take apart a 500 dollar Dyson Supersonic hair dryer, keep its tiny high-speed compressor, and bolt on a metal 3D printed combustion chamber head. Integza modeled the new head with a hollow middle that pulls extra air into the flow to cool the engine and exhaust, had it printed by a commercial metal printing company (K3D, DMLS process), brazed in fuel lines, and lit it. The results are dramatic: the exhaust melted his anemometer blades, roasted a tomato in seconds, and at maximum power scorched his tripod. But there are no CAD files, no BOM, no instructions, and no measurements of thrust or exhaust speed. The metal part was not printed at home. If you are looking for a project to build, this is not it. If you want to see what a maker-grade jet engine experiment looks like before committing to a full turbine build, or you are researching combustion chamber design and cooling strategies, the video (1zSU2kLLXQY) is worth the watch. The single thing most likely to go wrong if you tried to replicate this: you would need access to metal 3D printing (which is not a desktop technology) and you would be working with open flame, high-temperature exhaust, and flammable fuel without the guidance of measured parameters or a tested design file.
IN THE REPO
GOOD TO KNOW
- —This is a documented build experiment, not a replicable project — there is no repository, no CAD files, no BOM, and no step-by-step instructions.
- —The metal combustion chamber head was printed by K3D, a commercial metal 3D printing company, using DMLS (lasers melting fine metal powder layer by layer, up to 8,000 layers).
- —Integza says this was a first test before a full metal 3D printed jet engine; thrust and exhaust speed were never measured because the exhaust melted the anemometer blades.
- —The video shows the build process and results but does not provide files or measurements to replicate the build.
- —No licence or open-source release — this is documentation of a one-off experiment.
- —A comparable small RC jet turbine (JetCat P100-RX) costs 2,449 euros.
Parts to buy
3 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
Can I build this?
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
Turn a 500 dollar hair dryer into a jet engine
Integza's build video showing the Dyson teardown, metal 3D printed combustion chamber head, fuel injection brazing, and testing (including the melted anemometer, roasted tomato, and scorched tripod)
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Watch the build video (The only documentation of the build — shows the Dyson teardown, metal part design, fuel system, and testing)
- 2.Understand that this is not replicable without the CAD files and a commercial metal 3D printing service(The combustion chamber head was printed by K3D using DMLS, not a desktop process, and the design files are not available)
KNOWN ISSUES
- The metal combustion chamber head was printed by a commercial metal 3D printing company (K3D, DMLS process) — this is not something you can print at home on a desktop FDM or resin printer, and the CAD files are not available.
- There are no measurements of thrust or exhaust speed because the exhaust melted the anemometer blades — you have no data to design safe clearances or predict performance.
- The Dyson Supersonic costs around 500 USD, so this is an expensive experiment even before the metal printing and fuel system.
- Integza calls this a first test before a full metal 3D printed jet engine, so the design is not optimized or final.
- You are working with open flame, high-temperature exhaust, and flammable fuel under pressure — this is not a beginner project and requires fire safety equipment and a contained test environment.
- A comparable small RC jet turbine (JetCat P100-RX) costs 2,449 euros, so if you want a working jet engine for RC applications, buying one is the practical path.
Can I actually build this?
Not without the CAD files for the combustion chamber head and access to commercial metal 3D printing (DMLS). The video documents an experiment but does not provide the files or instructions to replicate it.
How hot does the exhaust get?
Hot enough to melt the blades of an anemometer, roast a tomato in seconds, and scorch a tripod at maximum power. Integza did not measure the exhaust temperature or speed because the anemometer was destroyed.
Is this a real jet engine?
It is a combustion chamber head that adds flame to the high-speed airflow from a Dyson Supersonic's compressor. Integza calls it a first test before building a full metal 3D printed jet engine, so it is an experiment in that direction but not a complete turbine.
Why not just buy an RC jet turbine?
A small JetCat P100-RX costs 2,449 euros. If you need a working jet engine for RC applications, buying one is the practical path. This project is for someone researching combustion chamber design or experimenting with maker-grade turbine builds.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
The exhaust was hot enough to melt the anemometer blades and scorch a tripod, but Integza never measured thrust or exhaust speed. If you were designing a test rig for a project like this, what would you measure first?
Integza (Joel)
Integza is a maker and YouTuber known for experimenting with jet engines, 3D printing, and high-temperature builds. This project was a first test before building a full metal 3D printed jet engine, documented in a video published 6 April 2023.
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM26d ago
Practical notes from our verification: this is documentation of a one-off experiment, not a replicable project — there is no repository, no CAD files, and no step-by-step instructions. The metal combustion chamber head was printed by K3D, a commercial metal 3D printing company, using DMLS (lasers melting fine metal powder layer by layer, up to 8,000 layers), not a desktop process. Integza's video (1zSU2kLLXQY) shows the build and testing but does not provide measurements or files. The single biggest limitation is that you cannot replicate this without access to commercial metal 3D printing and the missing CAD files, and the lack of measured thrust or exhaust speed means you would be testing blind.