TURN AN OLD RACING DRONE INTO AN UNDERWATER DRONE
Brushless motors run fine underwater, and a cable up to a floating box solves the problem that radio barely travels through water.
by Simon (RCLifeOn)
- difficulty
- ●●●●○
- time
- several weekends
- license
- license not specified
- repo
- repo
●●●●○ · several weekends · license not specified · repo
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
This is a proof of concept, not a build guide. Simon from RCLifeOn reused the motors and speed controllers of one of his old FPV racing drones, put them in a 3D printed body with two motors facing up and two facing forward, and solved the underwater radio problem with a hybrid: an eight-wire ethernet cable runs up to a floating box that holds the video transmitter and radio receiver. He says the motor and speed controller are worth about two pizzas on eBay, but you need a bunch of other parts too. The video explains the main ideas: BLHeli speed controllers switched to bi-directional for steering, the pin assignment of the eight-wire cable, a battery sealed inside with an XT60 port and an XT60 on/off connector on the outside, a lid sealed with epoxy and tested partially submerged for an hour, and mirrored propellers that cured torque roll. There are no files, no measurements and no written instructions, so you would design your own body and seal. The onboard camera looks like a potato next to the GoPro footage, and after the ocean trip one speed controller was damaged and the motors were nearly stuck, so this is a lake project, not an ocean ROV. The single thing most likely to go wrong: water getting into a body you designed yourself.
IN THE REPO
GOOD TO KNOW
- —This is a YouTube build video, not a repository. There are no STL files, no firmware, no written instructions, and no bill of materials.
- —The build requires reprogramming BLHeli speed controllers to bi-directional mode, which is mentioned but not explained in the video.
- —The 3D printed enclosure design is visible in the footage but not shared.
- —The eight-wire ethernet cable pin assignment is explained in the video (pins 1 to 4 motors, 5 the FPV camera, 6 and 7 spare, 8 common ground), but there is no written wiring diagram.
- —No licence applies because there are no released files.
- —Simon (RCLifeOn) filmed this as part two of his underwater drone series, not as a reproducible guide.
Parts to buy
12 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
- Motors and BLHeli speed controllers from an old FPV droneFind
- Power distribution boardFind
- FPV cameraFind
- Video transmitter and receiverFind
- Radio receiverFind
- Eight-wire ethernet cable and 8-pin connectorFind
- LiPo batteryFind
- XT60 connectorsFind
- Floating boxFind
- Plexiglass for the front windowFind
- Threaded insertsFind
- EpoxyFind
Can I build this?
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
Underwater drone, part two (RCLifeOn)
The video shows the build process and lake testing but does not provide step-by-step instructions or release any files. Timestamps from the transcript: salvaged parts value 00:43, motor orientation 00:03, BLHeli reprogramming 00:23, brushless motors in water 01:03, commercial drone cable comparison 01:24-01:45, floating box solution 02:06-03:07, battery and charging 04:35-05:38, propeller mirroring fix 08:47-10:11, depth control 10:11, camera quality 10:31, ocean damage 11:13 and 13:12.
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Watch the video and take notes on the body, motor placement, cable pin assignment and sealing (This is not a step-by-step guide; the video explains the ideas, not the measurements)
- 2.Design your own 3D printed enclosure sized for your specific motors and electronics(The enclosure in the video is custom and not shared)
- 3.Source salvaged FPV motors and BLHeli speed controllers, or buy equivalent parts(Simon mentions these are worth about two pizzas on eBay but does not specify models)
- 4.Reprogram the BLHeli speed controllers to bi-directional mode for reversible motor control(The video mentions this but does not explain how; you will need to research BLHeli configuration separately)
- 5.Leak-test the sealed body in shallow water before taking it to a lake(Simon left the sealed body partially submerged for one hour before the lake test, and kept a rope on the floating box)
KNOWN ISSUES
- There are no files, no BOM, and no written instructions. You are reverse-engineering a build from video footage, which is far harder than following a guide.
- The video only says the BLHeli speed controllers were switched from normal to bi-directional, which is required for steering. It does not walk through the configuration, so you will need to research that separately.
- The enclosure design is custom for Simon's specific motors and electronics. You cannot print a file; you have to design your own and get the sealing right.
- The onboard camera quality is far worse than the GoPro footage shown in the video. If you want usable live video, budget for a better camera.
- After the ocean trip one speed controller was damaged and the motors were nearly stuck. Treat this as a lake project with a rope on the floating box, not an ocean ROV.
- The floating box is only shown briefly: two batteries for weight and stability, the video transmitter with a big heatsink and a fan, a voltage regulator for the receiver, all sealed with epoxy. There are no plans for it, so you will design and waterproof your own.
Are there STL files or a parts list?
No. This is a YouTube build video, not a released project. The enclosure, wiring, and floating box are visible in the footage but not shared as files or documented instructions.
Can I use any brushless motors?
Brushless motors run fine underwater because the windings are insulated, but you need motors and speed controllers that can be reprogrammed to bi-directional mode for reversible thrust. Simon used salvaged FPV racing drone parts but does not specify models.
How deep can it go?
The video does not give a depth rating. The 3D printed body has a lid sealed with epoxy that held for an hour partially submerged, but it was not pressure tested, and after the ocean trip a speed controller was damaged. This is a lake project, not a rated ROV.
Why a tethered floating box instead of a waterproof radio inside?
Radio signals barely travel through water. Commercial underwater drones use a long data cable for this reason (Simon shows a 3,000 dollar one with a 100 meter cable). His floating box keeps the video transmitter and radio receiver on the surface, and only an eight-wire ethernet cable goes down to the drone.
How long does the battery last?
The video does not state battery capacity or runtime. The battery stays sealed inside; it is charged through an XT60 port on the outside, and a second XT60 connector works as the on/off switch.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
A commercial underwater drone like the 3,000 dollar one Simon shows comes with a 100 meter cable, while his version reuses an old FPV racing drone and a floating box. Would you design your own body and seal, or save up for a commercial one?
Simon (RCLifeOn)
Simon runs the RCLifeOn YouTube channel. This underwater drone was part two of his series, after the first version was beaten by the water. He built it from the parts of one of his old FPV racing drones, tested it in a lake and then in the ocean, where it did not go as planned and a speed controller was found damaged afterwards.
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM25d ago
Practical notes from our verification: this is a YouTube build video, not a repository, so there are no files to download and no written instructions. The video does explain the key ideas: bi-directional BLHeli speed controllers, the eight-wire cable pin assignment, the floating box contents, an epoxy-sealed lid with an outside XT60 charging port and on/off connector, and mirrored propellers against torque roll. What it does not give you is measurements, so you design your own body and seal, and water getting in is what will ruin your weekend. The onboard camera is visibly low resolution next to the GoPro footage, and after the ocean trip a speed controller was damaged, so this is a lake project, not an ocean ROV. The hybrid tether idea is the clever part.