BUILD AN AIRCRAFT CARRIER CATAPULT

A magnet rail that throws a real RC plane to 10 meters per second in a tenth of a second, using the same principle as a carrier catapult but with slot-car brushes.

by Tom Stanton

WorkshopRobotics

difficulty
●●●●○
time
a weekend-plus
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is Tom Stanton showing you how to build an electromagnetic launcher that works like a carrier catapult: a copper coil on a sled runs between rows of magnets, and metal contact strips flip the coil polarity at every magnet pair so it gets pushed then pulled all the way down the rail. At 48 volts it draws almost 90 amps, hits 44 mph, and launches a 138 gram RC plane to flying speed in a tenth of a second. It is a brilliant demonstration of the principle and the footage is spectacular. What it is not: a beginner project, a practical launch system, or a repo with files you can download. The single hardest part will be the brushes and contacts — they spark, they wear out fast under 90 amps, and you are fitting 80 of them by hand with no template. The video is clear about what is happening but you are reverse-engineering the dimensions and the wiring from the footage. High current, exposed contacts, and open sparking mean this is strictly for someone who already works comfortably with power electronics and has a proper bench supply. If you want a working electromagnetic launcher and you are happy to figure out the mechanical details yourself, this is the walkthrough. If you want plans, a BOM, and a safe first build, this is not it.

GOOD TO KNOW

  • —This is a YouTube build walkthrough, not a repository with files or a parts list.
  • —No CAD files, no cut list, no wiring diagram, no bill of materials.
  • —The video shows the build process and explains the mechanical timing system in detail.
  • —You will be fitting 80 magnets and 80 contacts by eye, which took the builder six and a half hours.
  • —No licence applies because there are no files to distribute.
  • —The builder states openly that this is not the most practical way to launch a model plane.

Parts to buy

7 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Neodymium magnets (80)Find
  • Copper wire for the coilFind
  • Metal contact stripsFind
  • BrushesFind
  • Aluminium railFind
  • 48 V high-current power sourceFind
  • Light RC plane (his is 138 g)Find

Can I build this?

Print3D printed sled parts and clear resin magnet holders (he uses Prusa and Formlabs printers); no files are published
Buyneodymium magnets (80), copper wire for the coil, metal contact strips, brushes, aluminium rail, a 48 V high-current power source, a light RC plane (his is 138 g)
Tools3D printer (FDM and resin), soldering iron, multimeter, hand tools, a power source that can deliver very high current at 48 V
Skillshigh-current wiring, coil winding, mechanical alignment, live testing under load — this is not a first electronics project
Timea weekend-plus — fitting 80 magnets and 80 contacts alone took six and a half hours, and that assumes you already have the rail built and the coil wound
Cost$$ — dominated by the high-current power supply and the magnets; the builder does not give a total
Safety90 amps at 48 volts with exposed brushes and open sparking contacts. Real risk of burns, shorts, and component destruction if the brushes fail under load. Not safe for beginners.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Electromagnetic Aircraft Launcher

0:20 mechanical timing system; 1:01-2:23 contact strips and brushes; 2:44 polarity flip at each magnet pair; 5:31 80 magnets and 80 contacts; 11:09-12:51 voltage tests and 44 mph run; 13:12-14:41 plane launch at 10.2 m/s

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the video (The entire build is shown in the footage — no separate instructions exist.)
  2. 2.Source the magnets and contact materials(You will need 80 neodymium magnets and 80 contact strips; the video does not give part numbers.)
  3. 3.Test at low voltage first(He tested at 16, 32 and 48 volts and compared several sled designs before the final launch; start low and work up.)

KNOWN ISSUES

  • The video does not include a parts list, so you are reverse-engineering magnet size, wire gauge, and contact strip dimensions from the footage.
  • Brushes wear out fast at 90 amps — the builder says the 48-volt test destroyed them, so budget for spares and expect to replace them regularly.
  • Fitting 80 contacts by hand with no jig took six and a half hours, and misalignment will cause the coil to miss a magnet pair and lose thrust.
  • A bench supply that can deliver 90 amps continuously is not cheap, and anything less will limit your top speed.
  • The builder states plainly that this is not the most practical way to launch a model plane — it is a proof of concept, not a field-ready system.
  • High current and exposed sparking contacts mean a short or a failed brush under load can destroy components or cause burns.

Is this the same system the Navy uses?

No. It works on the same idea, pushing and pulling a coil between magnets, but the Navy system uses very different electronics and launches full size jets. This one uses mechanical timing with slot-car style brushes and only handles light RC planes.

Can I build this without a high-current power supply?

You can test at lower voltages — the builder tried 16 and 32 volts — but the plane launch requires 48 volts and almost 90 amps. Anything less will not reach flying speed.

Why does it spark so much?

The brushes carry 90 amps and they break contact every time the coil flips polarity. That is 80 make-and-break events per run at high current, so sparking is unavoidable.

How long do the brushes last?

The 48-volt test destroyed the brushes. Budget for replacements and expect to rebuild them regularly if you are running at full power.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Eighty magnets, eighty contacts, six and a half hours of fitting, and a system that destroys its own brushes at full power — but it throws a real RC plane to flying speed in a tenth of a second. Would you build this as a proof of concept, or is there a more practical electromagnetic launcher design you would try first?

CompareeTEAM13d ago

Practical notes from our verification: this is a YouTube build with no repository, no files, and no parts list — everything comes from watching the video and reverse-engineering the dimensions. The builder is completely honest that this is not a practical launch system and the brushes do not survive high-current runs, which is rare candour for a project video. The single biggest challenge is not the magnets or the coil, it is fitting 80 contact strips by hand with no jig and getting the timing right so every magnet pair fires in sequence. If you already work with high-current systems and you want to prove the principle, the video gives you everything you need to know. If you want a safe first electronics project or a finished design you can replicate exactly, this is not it.

Tom Stanton

Tom Stanton builds working demonstrations of engineering principles on YouTube, often taking something expensive or complex and proving the concept with workshop materials and a camera. This launcher started as a question about how carrier catapults work and turned into a six-and-a-half-hour contact-fitting session.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.