TURN A BROKEN DYSON VACUUM INTO A PLANE

Two Dyson handheld vacuum motors, 3D printed ducts, and no propeller — it flies on centrifugal thrust alone.

by rctestflight

RoboticsWorkshop

difficulty
●●●●○
time
Not stated in the video; built and tested over several sessions
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a fascinating experiment that shows two vacuum motors can keep an RC plane in the air, but it is not a project you can replicate without significant design work of your own. The video gives the concept and the numbers — about 220 grams of thrust at 350 watts per motor, enough for the plane to climb on its own and soar — but there are no files, no parts list and no step-by-step guide on this page. You will be working from footage. The key part is the 3D printed snail housing that turns the motor's sideways blast into thrust, and you will be designing that yourself. The motors come from broken Dyson handhelds, so your build depends on finding donor units. There is no proportional throttle: the motors are switched on by hand and a servo flips the switches off, and those switches are rated for about 5 amps and half-welded themselves under the real current. It is not a jet engine, and the creator himself calls it extremely inefficient. If you are an experienced RC builder comfortable with CAD and LiPo safety, it is a fun oddball propulsion experiment. If you need files and instructions, treat it as inspiration rather than a build guide.

GOOD TO KNOW

  • —This is a YouTube video build, not a repository project. There are no CAD files, no STL files, no bill of materials, and no written instructions.
  • —The 3D printed snail housing is shown in the video, but no model files are offered on this page. You will need to design your own housing from the footage.
  • —The plane's motors came from broken Dyson handheld vacuums taken apart for the build. The roadside vacuum that started the idea was repaired with a new battery and kept as a vacuum.
  • —The airframe uses 6 mm Depron foam, carbon tubes, Hitec HS-5055MG servos and a flight controller running ArduPilot, but there is no wiring diagram or written parts list.
  • —There is no licence. This is a one-off experiment shared on YouTube, not a reproducible open-source project.
  • —The creator himself calls it extremely inefficient and says centrifugal blowers are not good for RC planes. The motor switches half-welded themselves when switched on. It is not a jet engine, there is no combustion. This is a proof of concept, not a practical design.

Parts to buy

9 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Two broken Dyson handheld vacuumsFind
  • 6S LiPo batteryFind
  • RC transmitter and receiverFind
  • Flight controllerFind
  • Servos for the control surfaces and the switch cut-offFind
  • 6 mm Depron foamFind
  • Carbon tubesFind
  • Epoxy fairing compoundFind
  • Glue and packaging tapeFind

Can I build this?

Printsnail-shaped blower housings (FDM printed in two halves, smoothed with epoxy fairing compound) and a bell-mouth intake flare; the flare made no measurable difference in the creator's test. No files are offered here
Buytwo broken Dyson handheld vacuums, 6S LiPo battery, RC transmitter and receiver, flight controller, servos for the control surfaces and the switch cut-off, 6 mm Depron foam, carbon tubes, epoxy fairing compound, glue and packaging tape
ToolsFDM 3D printer, sandpaper, clamps, glue, a scale and rail for thrust testing, CAD software to design the housings, LiPo charger
Skillsintermediate to advanced — RC plane building experience, basic aerodynamics, CAD modelling for the thrust ducts, LiPo battery safety, soldering and wiring
TimeNot stated in the video. The build ran over several sessions: designing and printing the housings, building the airframe, a first test glide, then adding ailerons before the powered flights
Cost$$. No total is given in the video. The main costs are broken Dyson handhelds, a 6S LiPo, RC radio gear and servos, foam and carbon tube for the airframe, and print material for the housings
SafetyThe motor spins very fast (the creator measured 82,500 RPM) and screams outside its housing, so keep it secured and keep fingers clear of the impeller. Each motor draws up to 350 watts from a 6S LiPo, and the switches, rated for about 5 amps, half-welded themselves; a welded switch means the servo cannot cut the power. LiPo batteries can catch fire if punctured, over-discharged or short-circuited, and the plane has no battery voltage feedback, so land early. Never leave LiPos charging unattended. Fly only in an open area away from people and animals.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Dyson vacuum motor RC plane build and test flight

The only documentation. The creator narrates the whole build: taking the motor apart, power and thrust measurements, printing and smoothing the snail housings, building the airframe, the switch-cutting servo, and several test flights including climbs and soaring. There is no written guide.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video and note the housing shape, the nozzle, the motor mounting and the switch-cutting servo (This is the only source. Pause and screenshot the duct cross-sections and the motor mounts.)
  2. 2.Source two broken Dyson handheld vacuums with working motors(The roadside vacuum only had one dead battery cell, so the creator repaired it and kept it. The plane motors came from broken units he took apart. Look for handhelds sold as broken.)
  3. 3.Design your own snail housing in CAD, using the video stills as reference(No files are offered here, so you are recreating the housing from what you see in the footage. The creator split it in half for FDM printing and smoothed the inside with epoxy fairing compound. Start simple and iterate based on thrust tests.)
  4. 4.Test one motor and duct assembly on a bench with a 6S battery before building the full airframe(The creator mounted the motor and housing on a rail with roller wheels pushing into a scale and got 190 grams, then 220 grams with a narrower nozzle, at 350 watts. Keep the motor secured and clear of hands while testing.)

KNOWN ISSUES

  • No duct files are offered here. You will be designing the snail housing yourself from the video, and your first version may not match the thrust numbers shown. Budget time for iteration.
  • The motors come from broken Dyson handheld vacuums taken apart for the build. The video does not give an exact model or part number, so check that your donor motor matches before designing a housing around it.
  • The motors have no proportional throttle. They are either on or off. A servo physically flips the switches to cut power, which is crude and limits your ability to control altitude and speed in flight.
  • The creator calls it extremely inefficient and says centrifugal blowers are not good for RC planes. Each motor draws up to 350 watts for about 220 grams of thrust, and the plane had no battery voltage feedback in flight. This is a proof of concept, not a practical design.
  • The motor switches are only rated for about 5 amps and half-welded themselves when switched on, because the motors draw far more. If a switch welds shut, the servo can no longer cut the power. Use parts rated for the real current.
  • The airframe ended up bigger than planned, so it needed a second motor from another broken Dyson. The first test glide also showed the tail elevons gave no roll control, so ailerons had to be added.

Where did the motors come from?

From broken Dyson handheld vacuums. The roadside vacuum only had one dead battery cell, so the creator replaced the battery and kept it as a working vacuum. To study the motor he bought a broken one and took it apart, and the second motor for the plane came from another broken Dyson. You will need broken donor units of your own.

How much thrust does one motor produce?

About 190 grams with the first housing, and about 220 grams after a narrower nozzle added 14 percent, at 350 watts on a 6S battery. Two motors were enough for the plane to climb on its own and soar, although the creator still calls the climb rate sluggish.

Is there a 3D model for the snail housing?

No files are offered on this page. The video shows how the housing was made: designed in CAD, split in half, FDM printed, smoothed inside with epoxy fairing compound, sanded and glued onto the motor. You will need to design your own from the footage.

Why use vacuum motors instead of normal RC motors and propellers?

This is a technical experiment, not a practical design. The creator wanted to see whether a Dyson motor moves enough air to fly an RC plane, and by his own words it is extremely inefficient: centrifugal blowers are not good for RC planes compared to a propeller. It is not a jet engine either, there is no combustion. It is interesting because it works, not because it is optimal.

How do you control the throttle?

You do not. The motors have no proportional throttle, so they are switched on by hand before launch and a servo flips the switches off to cut power. Once cut, the throttle cannot be turned back on in the air.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

He measured 220 grams of thrust at 350 watts per motor, enough to climb and soar — but the switches half-welded from the current and the whole thing is extremely inefficient. Would you try to improve the duct design, or is this just a one-off proof of concept?

CompareeTEAM17d ago

We checked the video against the creator's own numbers. The motors pull 120 watts on low and 350 watts on high through a tiny 21 millimetre intake, and the footage shows the plane climbing on its own and soaring with no propeller. What the video does not give you is a way to replicate it: no files, no parts list, and no housing geometry beyond what you can pause and screenshot. It is not a jet engine, and the creator himself calls it extremely inefficient and says centrifugal blowers are not good for RC planes. If you want to build one, you are designing the housings yourself and hunting for broken Dyson vacuums. Fascinating experiment, not a beginner build.

rctestflight

An RC experimenter who tests unusual ideas, from a laser lawnmower to a solenoid-powered peanut butter mixer. This build started when he found a Dyson handheld vacuum by the side of the road, fixed its battery, and was so impressed by its power that he wanted to see if the motor could fly a plane.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.