TURN AN OLD WACOM TABLET INTO A PEN DISPLAY

A bare iPad screen passes Wacom pen signals, so an old screenless tablet can become a pen display for about 80 dollars.

by Akaki Kuumeri

DisplaysWorkshop

difficulty
●●●○○
time
Not stated by the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a hack for someone who already owns an old screenless Wacom Intuos and wants a pen display without buying one; for reference, a Wacom Cintiq 16 launched at 649.95 dollars. The core insight is clever: the Wacom pen signal passes straight through a bare iPad screen, so you can strap a third-generation iPad screen onto the tablet and draw directly on it with pressure and tilt. The parts list is short: about 40 dollars for the screen, about 25 for a third-party HDMI driver board, a spare iPad glass, card and tape, around 80 dollars in total. The build assumes you are comfortable buying the screen as a replacement part, carefully sliding off its aluminium backing (Akaki calls it the most harrowing part), 3D printing a frame, and calibrating the tablet's active area to match the screen. The video shows the calibration step at 03:46 but does not walk through it. The single biggest trap is that without a Wacom already, this makes no sense: Akaki says at 04:06 that it is probably cheaper to just buy an iPad. But if you have an old Intuos lying around, this is a cheap way to turn it into a pen display, and because everything is taped on, the Wacom itself stays unmodified.

GOOD TO KNOW

  • —The build exists as a YouTube video only. The frame is 3D printed, but no frame files are linked.
  • —There is no written guide, no bill of materials file, and no repository.
  • —You need an old screenless Wacom tablet already. Without one, Akaki says it is probably cheaper to just buy an iPad.
  • —The iPad screen is bought as a replacement part, not salvaged from a working device.
  • —The aluminium backing must be removed from the screen or the pen will not work. That step is delicate.
  • —The whole assembly is taped onto the tablet, so the Wacom itself is not permanently modified.

Parts to buy

5 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Bare third-generation iPad screen~40 USDFind
  • HDMI driver board~25 USDFind
  • Spare iPad glassFind
  • Card stockFind
  • Double-sided tapeFind

Can I build this?

Print3D printed frame to hold the screen sandwich, printed in two pieces in the video. No files are linked.
BuyBare third-generation iPad screen (~40 USD), HDMI driver board (~25 USD), spare iPad glass, card stock, double-sided tape
Tools3D printer access, a way to cut card, tape, and a careful hand for opening the screen's aluminium backing
SkillsComfortable handling delicate electronics, calibrating input devices, basic 3D printing. The aluminium backing removal is the most critical step.
TimeThe creator does not give a build time. Allow extra time for removing the aluminium backing carefully and for calibrating the active area.
Cost$$ — about 80 USD for parts if you already own the Wacom tablet. The screen and driver board are the bulk of it.
SafetyThe bare screen and its yellow LED ribbon cable are fragile. Work slowly when bending the tabs and sliding off the aluminium backing, and watch the double-sided tape around the edges.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Strap-on pen display build by Akaki Kuumeri

The only documentation for this build. Shows the full process but does not link files or provide written steps.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the YouTube video (This is the only documentation. Pause and rewatch the frame assembly at 02:44-03:26.)
  2. 2.Source a bare third-generation iPad screen(Bought as a replacement part for about 40 dollars, not salvaged from a working iPad. The one in the video has an aluminium backing you will need to slide off.)
  3. 3.Buy an HDMI driver board that matches the screen(About 25 dollars in the video. It must work with the third-generation iPad panel; Akaki does not name the exact model.)
  4. 4.Print or fabricate the frame(No frame files are linked. You will likely need to design your own frame to fit your tablet and screen.)

KNOWN ISSUES

  • You must already own a screenless Wacom tablet. Without one, Akaki says at 04:06 it is probably cheaper to just buy an iPad. Do not start this build unless you have the Wacom already.
  • The aluminium backing on the iPad screen blocks the Wacom pen signal, so it has to come off. Akaki calls this the most harrowing part: peel the tape, bend the tabs open and slide it out carefully, watching the double-sided tape at the edges and the yellow LED ribbon cable.
  • The HDMI driver board must match the screen resolution and connector. The video does not name the exact model, so you will need to source one that fits a third-generation iPad panel.
  • The active area of the Wacom must be calibrated to match the screen size. The video shows this at 03:46 but does not explain how to do it. If the calibration is wrong, the pen position will not match the cursor.
  • No frame files are linked. You will likely need to measure your own tablet and screen and design a frame yourself.
  • The whole sandwich is held on with tape. If the screen shifts on the tablet, the active area no longer lines up and you will need to recalibrate.

Can I use a different iPad screen or a different tablet?

The video only shows a third-generation iPad screen on an A5-size Wacom Intuos, so other combinations are untested here. What the build shows is that a metal backing blocks the pen signal: the screen's aluminium backing had to come off before the pen worked through it.

Where are the STL files?

No frame files are linked. Akaki 3D printed a two-piece frame, but you will likely need to design your own to fit your tablet and screen.

Does this work with touch input?

The video only shows pen input through the Wacom. The iPad screen is driven over HDMI as a normal monitor; touch is not part of the build.

Is this reversible?

The Wacom itself is not modified: the screen sandwich is taped on and comes off anytime. The screen panel is changed, though, since its aluminium backing is slid off, and the video does not show putting it back.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

About 80 dollars for parts turns an old screenless Wacom into a pen display—if you already have the tablet. What would you use yours for?

CompareeTEAM23d ago

Practical notes from our verification: this build exists only as a YouTube video, and no frame files are linked, so you will likely need to design your own frame. The single biggest decision is whether you already own a screenless Wacom: Akaki says at 04:06 that without one it is probably cheaper to just buy an iPad, and we agree. The critical step is sliding the aluminium backing off the screen, which he calls the most harrowing part, so go slowly around the tape and the LED ribbon cable. If you have the tablet already and you are comfortable with delicate work, this is a clever hack. If you are starting from zero, it is not.

Akaki Kuumeri

Akaki Kuumeri strapped a bare iPad screen onto the old A5-size Wacom Intuos he has had for over 10 years, turning it into a pen display without modifying the tablet. He documented the build on YouTube and is on Instagram as @akakikuu.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.