TURN GLOW-IN-THE-DARK FILAMENT INTO A FAKE CRT THAT DRAWS WITH A LASER

A tiny fake CRT that draws vector graphics with a UV laser on glow-in-the-dark PLA, using 3D printed stepper galvos and an ESP32.

by bitluni

DisplaysWorkshop

Built withESP323D printing

difficulty
●●●●○
time
a weekend-plus
license
license not specified
repo
repo ACTIVE100 stars
1
Jump to section

COMPAREE VERDICT

This is bitluni doing what he does best: a weekend hack that makes you smile and then makes you think. The idea is clever — glow-in-the-dark PLA reacts to UV light just like phosphor on a CRT, so a moving laser dot leaves lines that fade slowly — and the execution is mostly 3D printed parts and cheap breakout boards. An ESP32 draws fonts, Lissajous curves, and even accepts XY scope signals from external probes. But the repository is skeletal. There is firmware for all three modes, STLs for the enclosure and galvo, and that is it. No schematic, no wiring photo, no instructions on how to align the mirrors or tune the microstepping. You will be pausing the video every ten seconds to see where a wire goes. If you have built a few of bitluni's projects before and you are comfortable reverse-engineering from footage, this is a great weekend-plus. If you need a BOM and a step list, wait for someone else to document it first.

GOOD TO KNOW

  • —STL files and Blender source are in the repo (case, galvo, mirror, screen).
  • —Three separate firmware sketches: Arduino Nano for the steppers, ESP32 for patterns, ESP32 for websocket drawing.
  • —No schematic, no wiring diagram, no assembly instructions.
  • —No BOM — you follow the video to identify parts (Arduino Nano CNC set, ESP32 mini, stepper motors, purple laser pointer, knob encoder, BNC terminals, glow PLA).
  • —No licence file in the repository.

Can I build this?

PrintEnclosure (base, front, top), galvo assembly, two mirror mounts, glow PLA screen
Tools3D printer, soldering iron, multimeter, laser safety glasses (required), hot glue or epoxy for mirror mounting
SkillsIntermediate — 3D printing, basic wiring, firmware upload, and critically you need to be comfortable filling gaps from a video because there are no written instructions
TimeA weekend-plus: print time is a few hours, wiring and alignment will take longer than the prints
Cost$$: the steppers and the Nano CNC set are cheap, but glow filament, the ESP32 and a violet laser pointer add up.
SafetyLaser hazard: UV/violet laser pointers can cause permanent eye damage in under a second. Eye protection rated for the wavelength is required at all times during testing and use. Do not skip this.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

I made a fake CRT TV with a LASER

Shows the galvo assembly, failed attempts with speakers and servos, microstepping tuning, and all three firmware modes. Sponsored by Brilliant.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the video first (The repo has no instructions, so the video is the build guide. Take notes on wiring and mirror alignment.)
  2. 2.Print the enclosure and galvo parts (Six STLs: case base/front/top, galvo, mirror mount, screen. The screen is printed in glow PLA.)
  3. 3.Order the Arduino Nano CNC set and steppers(This is the galvo driver and the motors.)
  4. 4.Flash firmware to the Arduino Nano and ESP32 (Three sketches: StepperVectorCRT for the Nano, Pattern and OsciVector for the ESP32 depending on mode.)

Resources

Documentation, files and community threads for this build — we link straight to the original sources and never rehost the creator’s files.

KNOWN ISSUES

  • The biggest mistake happens before you start: buying a laser pointer without also buying laser safety glasses rated for the wavelength. UV and violet lasers are not toys.
  • There is no wiring diagram. You will be scrubbing through the video to see where each wire goes, and the camera does not always show it clearly.
  • Mirror alignment is critical and the repo does not document it. If the beam does not hit the screen square, the whole thing fails.
  • The firmware has hardcoded pins and speeds. If your steppers are different or your mirrors are heavier, you will be editing code and recompiling.
  • Glow PLA reacts strongly to violet and UV light and much less to a red laser, so the laser colour matters.

Is this actually a CRT?

No — it is a laser vector display that mimics the look of a CRT by using glow-in-the-dark material that fades like phosphor. There is no electron beam or vacuum tube.

Can it display video or TV signals?

No. It draws vector shapes (lines, fonts, Lissajous curves) one segment at a time. The XY mode accepts external analog signals like an oscilloscope, but it is not a raster display.

Do I really need laser safety glasses?

Yes. UV and violet lasers can cause permanent eye damage faster than your blink reflex. The video mentions it multiple times; do not run this without proper eye protection.

What is the Arduino Nano CNC set?

A cheap stepper driver set for an Arduino Nano. He lists it at about 5 dollars in the video description.

Does drawing speed matter?

Yes. The menu has a speed setting, and at the fastest speeds the drawing quality visibly drops.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The whole thing runs on a five-dollar CNC shield and steppers you can micro-step down to smooth motion — but faster drawing means dimmer lines. What would you display first: fonts, Lissajous curves, or scope traces?

CompareeTEAM1mo ago

Practical notes from our verification: the repository has the STL files, the Blender source and three firmware sketches (StepperVectorCRT for the Nano, Pattern and OsciVector for the ESP32), but no schematic, no assembly guide and no licence file. The video is the real documentation. The one thing that is not optional is eye protection: bitluni says to wear it at all times around the laser.

bitluni

bitluni is a YouTuber and engineer known for weekend hacks that mix nostalgia, lasers and cheap hardware. This fake CRT follows his previous video, a mechanical spinning-disc TV.

GitHub

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.