TURN A CHEAP DRONE INTO A THERMAL DRONE

A 200 dollar thermal module and a 3D printed mount turn a GPS drone into a thermal drone for under 500 dollars.

by Hoarder Sam

RoboticsOpen-hardware

Built with3D printing

difficulty
●●●●○
time
Build time not stated by the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Hoarder Sam mounted a 200 dollar AliExpress thermal camera next to a normal FPV camera on his GPS drone, and it works: warm things like people, cars and street lights stand out clearly at night, and the sun does not wash the image out during the day. The whole build came in under 500 dollars, against over 7,000 dollars for DJI's thermal drone. The 256-pixel resolution is far below DJI's, and he says plainly it is not as capable, but it is the kind of view that helps with search work, finding lost animals or spotting heat leaks. The key choice is the module: the 256-pixel version with the older 9 mm lens only sees about 20 degrees, while the newer 4 mm lens widens it to about 55 degrees. Flying on the thermal view alone is hard, which is why he uses a drone with iNav position hold and switches between the two cameras. His camera mount is on MakerWorld and the video shows his final wiring diagram, but there is no parts list file or code. Night flying has rules in most countries, so check your local drone rules before you fly.

GOOD TO KNOW

  • —There is no repository, parts list file or code. The video shows the build and the final wiring diagram.
  • —The drone comes from the creator's earlier 150 dollar autonomous drone build video.
  • —You source the thermal module yourself on AliExpress. Make sure it is the 256-pixel version with the 4 mm lens.
  • —The creator's 3D printed camera mount is on MakerWorld, linked from the video description.
  • —Night flying has rules in most countries. Check your local drone rules before you fly.

Parts to buy

5 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • 256-pixel thermal module with the 4 mm lensFind
  • GPS drone running iNavFind
  • Analog FPV cameraFind
  • Video switcherFind
  • Optional 5 V video recordersFind

Can I build this?

PrintCamera mount for the thermal and FPV cameras (the creator's mount is on MakerWorld) and a plate that holds the cameras and recorders
Buy256-pixel thermal module with the 4 mm lens, a GPS drone running iNav, an analog FPV camera, a video switcher (or a flight controller with built-in camera switching), optional 5 V video recorders
Tools3D printer, flight controller setup in iNav, an analog monitor or goggles for testing
SkillsFPV flying, iNav flight controller setup, wiring cameras and a video switcher at 5 V. This is not a first drone build.
TimeNot stated by the creator. He built it in stages: camera test, bench test, then drone install.
CostUnder 500 dollars complete, per the creator. The thermal module is about 200 dollars and the drone came from his earlier 150 dollar build.
SafetyUse it for things like search, lost animals or heat leaks. Night flying has rules in most countries, so check your local drone rules before you fly. Check voltages before wiring: the video recorders only take 5 V. Keep wires tidy so they cannot catch in the propellers.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Turn a cheap drone into a thermal drone

Compares the thermal module options, tests the camera on the bench, shows the dual-camera mount, the wiring diagram and the install, then day and night flight footage.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video and pick the 256-pixel thermal module with the 4 mm lens (The same module with the older 9 mm lens only sees about 20 degrees. The 4 mm lens widens it to about 55 degrees.)
  2. 2.Build or source a GPS drone running iNav with position hold(The creator uses the drone from his earlier 150 dollar build. Position hold lets you watch the thermal view without the drone drifting.)
  3. 3.Print the camera mount and wire the two cameras through a video switcher (The video shows his final wiring diagram. Watch the voltages: the video recorders only take 5 V.)
  4. 4.Check your country's drone regulations for night flying(Night flying has rules in most countries. Check your local drone rules before you fly.)

KNOWN ISSUES

  • Buying a thermal module without the 4 mm lens. The older narrow-lens versions have a roughly 20-degree field of view, which makes it almost impossible to find anything from altitude.
  • Assuming this is a beginner drone build. You need a working GPS drone with iNav and position hold before you start. Flying on thermal alone is hard.
  • Night flying without checking the rules. Night flying has rules in most countries, so check your local drone rules before you fly.
  • Expecting commercial thermal quality. The 256-pixel image is visibly coarse and the creator says plainly it is not as capable as the 7,000 dollar DJI.
  • Powering the 5 V video recorders from the camera pad. On his SpeedyBee Wing Mini the camera pad outputs full battery voltage, which would fry the recorders, so he takes 5 V from the servo pins instead.
  • Under-powering the video switcher. Its inputs and outputs are on separate voltage buses, so both lines need 5 V. If your flight controller has built-in camera switching, you can skip the external switcher.

Is there a mount I can print?

Yes. The creator's 3D printed thermal camera mount is on MakerWorld, linked from the video description, and the video shows his final wiring diagram. There is no parts list file or code.

What thermal module exactly do I need?

The 256-pixel module with the newer 4 mm lens, which gives about a 55-degree field of view. It costs about 200 dollars on AliExpress. The same module with the older 9 mm lens only sees about 20 degrees, which the creator calls cheap but not very useful.

Do I need the GPS drone from his earlier build?

You need a drone with GPS position hold. He used the drone from his earlier 150 dollar build, running iNav. You could mount the cameras on a traditional FPV drone, but he wanted position hold so the drone would not drift while he watched the thermal view.

Is 256 pixels enough?

For spotting heat sources like people, animals and cars, the creator says it does the job. It is far below DJI's resolution, and he says himself it is not as capable as the 7,000 dollar DJI drone.

Can I fly this at night legally?

Night flying has rules in most countries. Check your local drone rules before you fly.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

A 200 dollar thermal module with a 4 mm lens gives about a 55-degree view for an under-500-dollar build. What would you use a thermal drone for: finding lost pets, spotting heat leaks, or something else?

CompareeTEAM21d ago

Practical notes from our verification: there is no repository, parts list file or code, but the creator's camera mount is on MakerWorld and the video shows his final wiring diagram. The drone is from his earlier 150 dollar build, running iNav for position hold. The thermal module is the 256-pixel AliExpress unit with the newer 4 mm lens, which widens the view from about 20 to 55 degrees. Footage shows warm things like people, cars and street lights standing out clearly at night, and the image holds up in daylight. The biggest trap is buying the module with the old narrow lens. The second is voltage: his flight controller's camera pad outputs full battery voltage, which would fry the 5 V recorders.

Hoarder Sam

Hoarder Sam builds FPV drones and posts the builds on YouTube. This thermal drone combines a 200 dollar AliExpress thermal module with the GPS drone from his earlier 150 dollar autonomous drone build, for under 500 dollars total.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.