TURN ROPE AND 3D PRINTED DRUMS INTO A ZERO-BACKLASH ROBOT GEARBOX

A rope-driven speed reducer with zero backlash, 3D printed drums, and 13 Nm of torque from steel wire wrapped around a brushless motor.

by Aaed Musa

RoboticsOpen-hardware

Built with3D printing

difficulty
●●●●○
time
a weekend-plus
license
license not specified
repo
repo ACTIVE654 stars
1
Jump to section

COMPAREE VERDICT

This is a genuine alternative to harmonic drives for robot joints, and Aaed Musa has already put it through load tests and built working robots with it. The principle is elegant: a small drum and a big drum linked by rope under tension, so the reduction ratio is just diameter divided by diameter and there are no teeth to introduce backlash. His test stand hit 13 Nm of torque swinging 5 lb loads, all from 3D printed parts and stainless steel wire. The problem is that the shared files cover the test stand, not the robots, and there are no instructions for tensioning the wire or tuning the system. The ODrive S1 and a 90 KV brushless motor are not cheap buys, and if you have never worked with field oriented control or tensioned a capstan before, you will spend more time troubleshooting than the several months of prototyping he already put in. The write-up on his site adds context but no step-by-step guidance. This is a proven concept with real footage of working robots, but you are building from CAD and a BOM rather than a guide, and the single biggest trap is underestimating how much tuning the rope tension will cost you.

GOOD TO KNOW

  • —STEP files for all 3D printed parts (base plate, drums, motor magnet holder, slider, brace, assembly jig)
  • —BOM spreadsheet covers the test stand only, not the quadruped leg or jumping robot shown in the video
  • —No firmware (the ODrive S1 controller ships with field oriented control)
  • —No build instructions, no tuning guide for the rope tension, no troubleshooting notes
  • —No licence file in the repository
  • —Last push 14 June 2024, no further commits since then

Parts to buy

5 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • ODrive S1 controllerFind
  • 90 KV brushless motorFind
  • 1.5 mm stainless steel wireFind
  • Lead screw hardwareFind
  • Bearings and fasteners (exact partsFind

Can I build this?

PrintBase plate, big drum, small drum, small drum cap, motor magnet holder, slider, brace, ODrive S1 single cover, assembly jig (all STEP files in the repo)
BuyODrive S1 controller, 90 KV brushless motor, 1.5 mm stainless steel wire, lead screw hardware, bearings and fasteners (exact parts in the BOM spreadsheet)
Tools3D printer, hex keys, tensioning tools for the lead screw
SkillsIntermediate 3D printing, brushless motor setup, ODrive tuning, mechanical assembly. The rope tensioning is trial and error if you have never built a capstan before.
TimeA weekend to print and assemble the test stand, then several more evenings tuning the rope tension and motor controller. Aaed spent several months prototyping.
Cost$$ — the ODrive S1 and brushless motor dominate the cost, the 3D printed parts and wire are cheap
SafetyNone beyond ordinary electronics care. The motor spins fast but there are no exposed high voltages, no lithium cells, no lasers.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

High Precision Speed Reducer Using Rope

The primary video, 3.0M views, uploaded 31 May 2024. Shows the capstan drive principle, load tests, the quadruped leg and the jumping robot.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Read the write-up on the project site (Context on the capstan principle and why Aaed built it, but no step-by-step instructions)
  2. 2.Watch the main video (Shows the working test stand, load tests, and the robots it drives)
  3. 3.Download the STEP files and BOM (All the CAD for the test stand and a spreadsheet of parts)
  4. 4.Print the drums and base plate first(The drums and base plate are the core parts of the test stand.)

Resources

Documentation, files and community threads for this build — we link straight to the original sources and never rehost the creator’s files.

KNOWN ISSUES

  • The BOM and CAD cover the test stand only — the quadruped leg and jumping robot shown in the video are separate builds with no shared files
  • Wire tension is critical and there is no written guide for it, only what the video shows.
  • The ODrive S1 and 90 KV motor are not beginner-friendly buys. If you have never tuned field oriented control, budget time for the learning curve.
  • No instructions means you are reverse-engineering the assembly from the STEP files and the video footage
  • The D:d ratio (drum diameter to rope diameter) has to be high for steel wire — if you try to substitute thicker rope or paracord without recalculating, the system will not work
  • No licence file in the repo, so the legal status for commercial use is unclear

Can I use paracord or fishing line instead of stainless steel wire?

His first prototype used shoelaces, so it works for experiments. The actuator in the video uses 1.5 mm stainless steel wire, and he explains that the drum-to-rope diameter ratio has to stay high for steel wire.

Is the ODrive S1 required, or can I use a cheaper motor controller?

He used an ODrive S1 with field oriented control, which turns the brushless motor into a precise servo. The video doesn't test other controllers.

How do I tension the rope?

The test stand uses a lead screw to tension the wire. There is no written tensioning guide, so the video is the reference.

Are the quadruped leg and jumping robot files shared?

No. The repo has the test stand only. The robots in the video are separate projects.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The test stand hit 13 Nm with 3D printed drums and steel wire, and Aaed has already built working robots with it — but the shared files stop at the test stand. If you were building this, would you start with the shoelace prototype to learn the tuning, or go straight to the steel wire version?

CompareeTEAM1mo ago

Practical notes from our verification: the repository has STEP files and a BOM for the test stand, but no build instructions and no firmware (the ODrive S1 ships ready to run). The write-up on aaedmusa.com adds context but no step-by-step guidance. The main video (3.0M views, 31 May 2024) shows the working system under load and the robots it drives, but the quadruped leg and jumping robot are separate builds with no shared files. The single biggest unknown is the rope tensioning — Aaed spent several months prototyping, and there is no shortcut guide for that learning curve. No licence file in the repo, so commercial use is unclear.

Aaed Musa

Aaed Musa builds robots and robot actuators on YouTube. For this video he spent several months prototyping a capstan drive, starting with shoelaces from an old pair of Nikes before moving to 1.5 mm stainless steel wire and 3D printed drums.

GitHub Web

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.