BUILD A 3D PRINTED JET THAT HITS 273 MPH

A student team 3D printed a 1 meter jet aircraft and hit 273 mph on the maiden flight.

by The Mach Initiative

RoboticsOpen-hardware

difficulty
●●●●●
time
multi-year team project
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

KingChaser is a research demonstration, not a weekend build. A team of University of Bath students spent three years developing it, starting with an electric prototype and a smaller 60 newton jet before arriving at the 300 newton turbine version that hit 273 mph. The airframe is 3D printed, but the engine, radio, flight controller, and sensors are all purchased. The plane pulled 11 G in the turns on that first flight, bending the wing roots enough that the team had to add more carbon fiber reinforcement. The landing broke the airspeed sensor and antenna, which the printed construction made easy to replace. This is not a project you can replicate from published files — none exist. It is a proof that a printed airframe can survive the speeds and forces of a micro turbojet, and a glimpse of what a university team can do with access to a private airfield and three years of iteration. The one thing most likely to go wrong if you attempted something similar: underestimating the structural loads. Eleven G is a punishing figure, and that was with carbon fiber spars already in place. If you are looking for a jet project you can actually build this weekend, this is not it. If you want to see what is possible and are prepared to start much smaller, the video documents the journey well.

GOOD TO KNOW

  • —This is a demonstration project, not a published build. No files, bill of materials, or build instructions are publicly available.
  • —The team is The Mach Initiative from the University of Bath. The primary source is their YouTube video posted 24 Oct 2026.
  • —The airframe is 3D printed with carbon fiber spars. The 300 newton micro turbojet engine and all electronics are commercial off-the-shelf parts, not designed or printed by the team.
  • —The aircraft is launched from a rail and flown in a private flying area with permission. It requires RC piloting skills and access to appropriate airspace.
  • —The 273 mph figure is from the maiden flight. The 550 mph target is a calculation. The current record for a jet-powered model is 465 mph.
  • —No licence information is available because no design files have been released.

Parts to buy

6 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • 300 newton micro turbojet engineFind
  • RC radio systemFind
  • Flight controllerFind
  • Airspeed sensorFind
  • Carbon fiber tubes and clothFind
  • Launch rail hardwareFind

Can I build this?

Printairframe components (specific models not published)
Buy300 newton micro turbojet engine, RC radio system, flight controller, airspeed sensor, carbon fiber tubes and cloth, launch rail hardware
Toolslarge-format 3D printer, carbon fiber layup tools, private airfield access, RC piloting certification or equivalent
Skillsadvanced RC piloting, composite reinforcement, aerodynamics, propulsion system integration, requires team coordination
Timethree years for the full development cycle (electric prototype, 60 N jet, 300 N jet)
Cost$$$ — dominated by the micro turbojet engine, flight electronics, and airfield access
SafetyReal risks: micro turbojet engines operate at extremely high temperatures and speeds, require proper training and fire safety equipment. High-speed flight demands appropriate airspace and observer protocols. 11 G structural loads during flight can cause catastrophic failure if the airframe is compromised. This is not a beginner project.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

The Mach Initiative — KingChaser maiden flight

Primary documentation of the 273 mph maiden flight, development history, and structural challenges. Posted 24 Oct 2026.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full build and flight documentation (The only public documentation available. Covers the three-year development from electric prototype through both jet versions.)
  2. 2.Understand this is a demonstration, not a published build(No CAD files, bill of materials, or build instructions have been released. You cannot replicate this project from available sources.)
  3. 3.If attempting something similar, start with electric propulsion and much smaller scale(The team built an electric prototype first, then a 60 newton jet, before moving to the 300 newton turbine. That progression was deliberate.)

KNOWN ISSUES

  • No build files exist. This is a university research project, not a published open-source design. You cannot download STLs and start printing.
  • Micro turbojet engines cost thousands and require specific fuel, starting procedures, and safety equipment. They are not hobby-grade components.
  • The 273 mph flight bent the wing roots even with carbon fiber spars already installed. Structural loads at high speed are severe and unforgiving.
  • You need access to a private flying area with permission. This aircraft cannot be flown at a public RC field or without proper clearance.
  • The 550 mph target is a calculation, not a measured result. The current record is 465 mph and has not been broken.
  • RC piloting at these speeds requires advanced skills and fast reflexes. The landing on the maiden flight broke the airspeed sensor and antenna despite the pilot's experience.

Can I build this from the video?

No. The video is a documentation of the flight and development, not a build guide. No CAD files, parts list, or assembly instructions have been published.

Is this the world record for an RC jet?

No. The current record for a jet-powered model is 465 mph. KingChaser hit 273 mph on its maiden flight and is targeting 550 mph in future attempts.

What broke on the landing?

The airspeed sensor and antenna. The team noted that a printed airframe makes these kinds of repairs straightforward.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The team hit 273 mph on the very first flight, then had to reinforce the wings after the airframe pulled 11 G in the turns. If you were building towards a 465 mph record attempt, what would you change first — the wing structure, the thrust-to-weight ratio, or the launch system?

CompareeTEAM10d ago

Practical notes from our verification: this is a documentation-only project with no released files, so it sits outside our usual build-ready catalogue. We included it because the video is a rare honest look at what it takes to fly a printed airframe at jet speeds — three years, two earlier prototypes, carbon fiber reinforcement that still bent under load, and a broken sensor on landing. The 550 mph target has not been reached; 273 mph is the measured figure. The current record is 465 mph. If you want to build a jet, start electric or with a much smaller turbine — that is exactly what this team did.

The Mach Initiative

A team of students from the University of Bath founded The Mach Initiative three years ago with the goal of building a record-breaking 3D printed jet aircraft. They progressed through an electric prototype and a 60 newton jet before achieving the 273 mph maiden flight with KingChaser.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.