TURN A 256GB IPHONE 17 PRO INTO A 1TB ONE

DirectorFeng ground off the original flash chip and soldered on a 1TB one — no software trick, actual board-level surgery.

by DirectorFeng

Open-hardware

difficulty
●●●●●
time
a full day
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is not a project you build. It is a demonstration of what is possible if you already run a phone repair shop. DirectorFeng took a 256GB iPhone 17 Pro, removed the logic board, ground the original flash chip off, cleaned hundreds of tiny solder pads, soldered on a new 1TB chip, then restored iOS from a Mac. The phone booted with 1TB and ran a storage benchmark. Apple charges 400 dollars more for the 1TB model; this needs gear most people will never own and skill that takes years to build. The flash chip comes from the parts market, not from Apple, and the video does not name a supplier. One mistake and you have bricked a 1,099 dollar phone. If you do not already solder BGA chips for a living, this video is for watching, not for doing.

GOOD TO KNOW

  • —This is a walkthrough video, not an open-source repository — there are no files to download.
  • —No schematic, no pinout diagram, no written steps. The whole process is in the 25-minute video with English subtitles.
  • —The 1TB flash chip comes from the parts market, not from Apple — no supplier links are given.
  • —No licence applies because this is a demonstration, not a released design.
  • —Voids warranty immediately and Apple will refuse service on a modified device.
  • —Requires professional microsoldering gear: hot air rework station, microscope, flux, solder paste, reballing jig.

Parts to buy

4 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • 1TB flash chip for the iPhone 17 ProFind
  • FluxFind
  • Solder pasteFind
  • Isopropyl alcoholFind

Can I build this?

Printnothing required
Buya 1TB flash chip for the iPhone 17 Pro (parts market, no supplier given), flux, solder paste, isopropyl alcohol
Toolshot air rework station, stereo microscope, chip removal tooling, tweezers, BGA reballing kit, ESD mat, Mac with iTunes/Finder for DFU restore
Skillsprofessional-level BGA soldering — you must already know how to reball and reflow multi-hundred-pin chips without bridging or lifting pads
Timea full day if you have done this before; longer if you have not
Cost$$$, dominated by the 1TB flash chip and the tools if you do not already own them
SafetyNo mains voltage or lithium hazards beyond the phone's internal battery. Real risk is financial: one mistake bricks an expensive device Apple will not repair.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

iPhone 17 Pro 256GB Not Enough — Can We Upgrade It to 1TB?25:00

25-minute walkthrough with English subtitles. Shows chip removal, pad cleaning, soldering and the iOS restore. No spoken narration.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video (There are no written instructions — the video is the entire guide.)
  2. 2.Source a compatible 1TB flash chip(DirectorFeng does not name the supplier, and the chip comes from the parts market.)
  3. 3.Set up a microsoldering workbench(Hot air station, microscope, flux, solder paste, reballing kit. If you do not already own these, the tooling cost exceeds the storage upgrade saving.)
  4. 4.Back up the phone and prepare a Mac with the latest iOS restore image(Once you remove the original chip, there is no going back.)

KNOWN ISSUES

  • Lifting a pad during chip removal. The BGA has hundreds of tiny solder points and one torn trace means the board is scrap.
  • Attempting this without a stereo microscope. You cannot see what you are soldering at this scale with the naked eye.
  • Expecting Apple to service the device afterward. Any modification voids warranty and Apple Stores will refuse to touch it.
  • Underestimating the skill floor. If you have never reballed a BGA chip, an iPhone 17 Pro is not where you learn — practice on donor boards first.
  • Assuming the storage will be as fast as Apple's. Third-party flash chips may not match Apple's binning and firmware tuning.

Does this work on other iPhone models?

DirectorFeng has done similar storage upgrades on other iPhones, iPads and Macs, but each model needs its own chip and its own process.

Where do you buy the 1TB chip?

DirectorFeng does not name the source. The chip comes from the parts market, not from Apple.

Will iOS detect that the storage was upgraded?

In the video, the phone booted with 1TB after the restore and ran a storage benchmark.

Is this cheaper than buying the 1TB model from Apple?

In total cost counting tools and risk, no, unless you already run a repair business.

Can you go back to 256GB if something goes wrong?

Only if you kept the original chip intact and can resolder it without damage. Most people grind it off and throw it away.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Apple charges 400 dollars to go from 256GB to 1TB at purchase — DirectorFeng did it for the cost of a parts-market chip and a day of microsoldering. Would you try this on your own phone, or is the brick risk too high?

CompareeTEAM7d ago

Practical notes from our verification: DirectorFeng's channel has no website and no supplier links, so you would be hunting parts listings yourself. The video has English subtitles but no spoken narration; the process is visible, but there are no written steps or a BOM. It shows every step of the solder work, but if you have never reballed a BGA chip, this is not where you start.

DirectorFeng

DirectorFeng runs a phone repair and modification channel on YouTube, specialising in board-level work that most repair shops will not touch.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.