BUILD THE OSCARS GLAMBOT

A high-speed camera slider that hits 24 km/h and nails the famous slow-motion red carpet move without the £85,000 robot arm.

by Henry Kidman

DisplaysWorkshop

difficulty
●●●●●
time
several weekends
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Henry Kidman noticed that the famous Glambot move on the Oscars red carpet is basically a fast straight line, so instead of replicating the £85,000 robot arm that does the real thing, he built a giant slider. Four salvaged 2-metre shower curtain rails, joined with laser-cut MDF and 3D-printed parts and later stiffened with 6 mm steel, carry a carriage pulled by a belt and a 6-horsepower servo motor. On a 1.6-metre run it reaches 24.5 km/h and pulls 27 m/s² of acceleration. For the slow motion he rented a 4K cinema camera shooting 1,000 frames per second with a DJI lidar autofocus system. He tested it in the workshop, on a salt flat at sunset, and finally on an actual red carpet event. To be clear: this is not a project you replicate part-for-part. There are no files, no BOM, and the camera alone is a professional rental. What you get is a 19-minute workshop log that shows someone solving a very specific problem by replacing complexity with speed on a straight line. The single biggest trap is underestimating the danger: a carriage moving this fast will cause serious injury if someone is in the way. If you are a filmmaker with access to servo suppliers and rental camera houses, this is a fascinating alternative to buying a robot. If you are a hobbyist, this is inspiration, not a weekend build.

GOOD TO KNOW

  • —This is a video build log, not a repository. No CAD files, no parts list, no code.
  • —Henry Kidman shows the build process in a 19-minute YouTube video with timestamps for each major decision.
  • —The camera is a hired 4K cinema camera shooting 1,000 fps, at $1,000 a day.
  • —Rails are four salvaged 2 m shower curtain rails joined with laser-cut MDF and 3D-printed parts; the flexing ends were later replaced with stiffer materials.
  • —Industrial servo is roughly 6 horsepower, which is not a hobby part.
  • —No licence information — this is workshop documentation, not open-source hardware.

Parts to buy

5 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Four 2 m rails (Henry salvaged shower curtain rails)Find
  • Industrial servo motor (6 hp, up to 25 Nm)Find
  • Timing belt and pulleysFind
  • 000 fps cinema camera hireFind
  • Lidar autofocus systemFind

Can I build this?

Print3D-printed carriage parts, later stiffened with 6 mm steel ends
Buyfour 2 m rails (Henry salvaged shower curtain rails), industrial servo motor (6 hp, up to 25 Nm), timing belt and pulleys, 1,000 fps cinema camera hire, lidar autofocus system
Toolsworkshop with metalworking tools, CNC or machine shop access for stiffer parts, electronics workbench, safety barriers for testing
Skillsmechanical design, high-speed motion control, industrial servo tuning, professional camera operation, risk assessment for fast-moving machinery
Timeseveral weekends for the slider, plus rental scheduling and location permits for testing
Cost$$$, dominated by the industrial servo and the camera rental at $1,000 per day
SafetyA carriage moving at 24 km/h in 1.6 metres is a serious crush and impact hazard. Keep people well clear of the rail during operation. Mains voltage for the servo motor. High-speed mechanical failure can send parts flying.

This build involves mains voltage — for adults comfortable with electrical work only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

The World's Second Fastest Camera Slider

The full build walkthrough with design decisions, materials, and test footage at three locations.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video (19 minutes, timestamped by build stage)
  2. 2.Source an industrial servo(6 hp or equivalent, with encoder and control board)
  3. 3.Design the rail system(Straight rails, belt drive, test rigidity before pushing speed)
  4. 4.Rent or borrow a high-speed camera(1,000 fps minimum, budget $1,000 per day for a hired 4K cinema camera)

KNOWN ISSUES

  • The camera is a rental-only cinema model. You will not own this hardware, and $1,000 per day is the entry point.
  • There is no parts list. Henry shows what he used, but finding an equivalent servo, encoder, and controller is your problem.
  • A 6-horsepower servo is not sold at hobby electronics shops. Expect industrial suppliers and long lead times.
  • The first carriage design (MDF and 3D prints) was not stiff enough. Expect iteration or machine shop access.
  • This moves fast enough to cause serious injury. You need safety barriers, a kill switch, and a clear exclusion zone during tests.
  • The famous Glambot move is linear, but adding pan or tilt for more complex shots is not trivial and not covered.

Can I use a cheaper camera?

Yes, but the Glambot effect depends on very high frame rates. 1,000 fps is the floor.

How much does the slider itself cost, without the camera?

Henry does not publish a cost for the slider. The rails were salvaged shower curtain rails; the big costs are the servo and the camera hire.

Is there a CAD file or BOM?

No. This is a workshop build log, not an open-source project. You are reverse-engineering from the video.

How dangerous is this?

Very. A carriage this fast is a crush hazard. You need physical barriers and nobody in the path during motion.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

24.5 km/h in 1.6 metres, powered by a 6-horsepower servo — and it nailed the shot on an actual red carpet. If you were building one, would you replicate the linear slider or go back to the robot arm idea?

CompareeTEAM12d ago

Practical notes from our verification: there is no repository, no BOM, and no licence. This is a video build log, not a project you clone. The camera is hired at about $1,000 per day, and the servo is an industrial part, not a hobby stepper. The single most valuable part of the video is Henry's explanation at 1:03–1:43 of why a slider works: the Glambot move is basically linear, so you can trade robot complexity for straight-line speed. If you are planning this, budget for iteration on the carriage stiffness — his first version (MDF and 3D prints at 2:03) was not rigid enough.

Henry Kidman

Henry Kidman is a filmmaker who wanted the Oscars Glambot shot without the £85,000 robot. His insight was that the move is basically a fast straight line, so he swapped the robot arm for a giant slider.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.