TURN USED DA VINCI SURGICAL TOOLS INTO YOUR OWN ROBOT

Bennett Stirton bought expired da Vinci tools on eBay and built a joystick-driven robot that grips, cuts and clips on his desk.

by Bennett Stirton

RoboticsOpen-hardware

Built withArduino3D printing

difficulty
●●●●○
time
a weekend-plus
license
license not specified
repo
repo ACTIVE87 stars
1
Jump to section

COMPAREE VERDICT

This is a show-and-tell build, not a build guide. Bennett Stirton documented the concept — a 3D printed motor pack that grips the four control discs on the back of a da Vinci instrument, pulls the tiny cables inside, and mounts on a monitor arm — but left out the steps to replicate it. The STL files and Arduino sketch are there, and the video description lists the electronics, but there is no pinout and no assembly notes. You will spend most of your time figuring out motor selection, wiring, joystick mapping and mechanical tolerances from the video alone. The instruments themselves are the other variable: used ones appear on eBay intermittently, condition is unknown, and you are buying expired medical hardware that hospitals discarded after 10 to 15 procedures. If you have done cable-driven mechanisms before and enjoy reverse-engineering from footage, this is a fascinating proof of concept. If you need a step-by-step, it will cost you far more time than a weekend. The single thing most likely to go wrong: buying instruments that arrive damaged or with seized cables, because there is no return policy on used surgical tools.

GOOD TO KNOW

  • —STL files, Onshape design and Arduino code are on GitHub (Project Salai).
  • —No BOM, no wiring diagram, no build instructions — you reverse-engineer from the video.
  • —The Arduino code is salai_code_v5.ino, an early prototype that drives one instrument at a time.
  • —No licence file in the repository.
  • —Used surgical instruments are for tinkering only, never for medical use.
  • —The robot does not operate on anything; it demonstrates control of the instrument mechanisms.

Parts to buy

6 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Used da Vinci instruments (eBay or a medical surplus vendor)Find
  • Four servosFind
  • PCA9685 servo driverFind
  • JoystickFind
  • 10k potentiometersFind
  • Small computer and an old monitor armFind

Can I build this?

PrintMotor pack housing, instrument mounting mechanism, all structural parts (STL files in repo)
BuyUsed da Vinci instruments (eBay or a medical surplus vendor), four servos, a PCA9685 servo driver, a joystick, 10k potentiometers, a small computer and an old monitor arm
Tools3D printer, soldering iron, basic hand tools, multimeter for motor testing
SkillsIntermediate to advanced: cable-driven kinematics, motor control, Arduino programming, mechanical troubleshooting without documentation
TimeA weekend-plus if you already know cable mechanisms and can reverse-engineer wiring; a week or more if you are figuring out motor selection and tolerances from scratch
Cost$$: the used instruments are the big variable, prices on eBay vary a lot; the electronics in the video description are cheap hobby parts
SafetyLow voltage electronics only. Used surgical instruments are sharp and must never be used for any medical purpose.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Building a DIY Surgical Robot

Bennett Stirton's full build story and demonstration, The video shows the mechanical design, motor pack assembly, instrument swapping mechanism and joystick control, but does not include step-by-step build instructions.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full YouTube video to understand the cable-driven mechanism and motor pack design (This is your primary reference — the GitHub files alone will not be enough)
  2. 2.Clone the Project Salai repository for STL files, Onshape model and Arduino code (salai_code_v5.ino is the firmware starting point)
  3. 3.Source used da Vinci instruments from eBay or a medical surplus vendor(Condition and availability vary; expect to pay per instrument and check cable function on arrival)
  4. 4.Print the motor pack housing and test-fit the motors before wiring(Motor shaft to disc coupling is the critical tolerance)

Resources

Documentation, files and community threads for this build — we link straight to the original sources and never rehost the creator’s files.

KNOWN ISSUES

  • Buying instruments with seized or broken cables — there is no return policy on used surgical tools, and you cannot test them before purchase.
  • Picking servos that are too weak or too strong: the instrument cables are tiny, and the video shows how easy it is to break one while testing.
  • Assuming the Arduino code is complete — it drives one instrument at a time and is labelled v5, implying earlier iterations.
  • Skipping the spring mechanism that allows instrument swapping — without it, you remove and reinstall the motor pack every time.
  • Expecting the robot to perform surgery or handle tissue — it is a demonstration rig for the control mechanism only.
  • Missing the fact that there is no wiring diagram — you map the joystick potentiometer to motor pins yourself.

Can I actually buy used da Vinci instruments?

Yes, they appear on eBay and medical surplus sites periodically. Hospitals sell or discard them after 10 to 15 uses. Condition is unknown, prices vary, and they are for tinkering only — never for medical use.

What parts does the build use?

The video description lists a PCA9685 servo driver board, a cheap joystick, 10k potentiometers and a small computer that runs everything. Four servos turn the four discs on the instrument.

Does the code control multiple instruments at once?

No. The Arduino sketch in the repository drives one instrument at a time. The video shows swapping instruments manually.

Is there a BOM or wiring diagram?

No. The repository contains STL files, the Onshape model and the Arduino sketch, but no parts list or wiring notes. You reverse-engineer from the video.

Can I use this for actual surgery?

Absolutely not. Used surgical instruments are expired and unsterile, the robot has no safety systems, and it is a demonstration build only.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Used da Vinci instruments expire after 10 to 15 procedures and end up on eBay — but condition is a gamble and there is no return policy. Have you sourced expired medical hardware before, and what did you learn about testing it before you build around it?

CompareeTEAM1d ago

Practical notes from our verification: the GitHub repository contains STL files, an Onshape link and the Arduino sketch (salai_code_v5.ino), but no BOM, no wiring diagram, and no build instructions. The YouTube video is the only real guide, and it shows the concept rather than the steps. The instruments themselves are the wildcard — availability and condition vary, and you are buying hardware that hospitals discarded after surgical use. The motor pack design is clever (a spring mechanism lets instruments swap in and out), but you will spend significant time reverse-engineering motor selection, tolerances and wiring from footage alone. This is a proof-of-concept build for someone who enjoys that kind of detective work, not a weekend project for someone expecting a step-by-step.

Bennett Stirton

Bennett Stirton built Project Salai after learning that da Vinci surgical robots cost about two million dollars and their instruments expire after 10 to 15 uses, with thousands discarded each year. He bought a set of used instruments on eBay and reverse-engineered the cable-driven mechanism to build his own desktop control rig.

GitHub

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.