TURN A CHEAP MINI MILL INTO A CNC MACHINE

Swap the lead screws for ball screws, add stepper motors and an ESP32 running FluidNC, and a hand-cranked mini mill becomes a three-axis CNC.

by Someone Should Make That

Workshop

Built withESP32

difficulty
●●●●○
time
Not stated; a long multi-step machining build
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a video build log of a mini mill turned into a three-axis CNC. To beat backlash he swapped the lead screws for ball screws, gave the Z axis a screw it never had, machined his own mounting plates and standoffs, and drives all three axes with open-loop stepper motors controlled by FluidNC on an ESP32. It suits someone who already does manual machining: the brackets were cut on a band saw and finished on a mill and lathe. The video is good at showing the real problems (hardened ball screws that had to be trimmed with abrasives, lost ball bearings, a first test that didn't move because of a wiring mistake), but there is no written guide, parts list or CAD to download. The test part came out square and about two thousandths undersize, while about four thousandths of backlash remains from the cheap imported ball screws. The creator didn't say what the whole conversion cost.

GOOD TO KNOW

  • —This is a video build log, not a GitHub repository.
  • —No CAD files, parts list or written instructions are published.
  • —The control firmware is FluidNC running on an ESP32.
  • —The video shows the main machining steps but skips much of the repetitive work, the wiring and the config files.
  • —The creator does not state the total cost of the conversion.
  • —About four thousandths of an inch of backlash remains from the cheap ball screws.

Parts to buy

6 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Ball screws and ball nutsFind
  • Standard ball screw supportsFind
  • Stepper motors and drivers (he bought them as a kit)Find
  • ESP32 boardFind
  • Motor couplingsFind
  • Flat plate for the brackets and standoffsFind

Can I build this?

PrintNothing required; he 3D printed a small tube to keep the ball bearings in when taking the ball nut off
Buyball screws and ball nuts, standard ball screw supports, stepper motors and drivers (he bought them as a kit), an ESP32 board, motor couplings, and flat plate for the brackets and standoffs
Toolsmill, lathe with a four-jaw chuck, band saw, fly cutter, rotary table, drill and taps, abrasive cutting tools
Skillsmanual machining (milling, lathe work, drilling and tapping), wiring stepper drivers, configuring FluidNC
TimeNot stated; the video shows a long build: cutting plate, milling, drilling and tapping, making 12 standoffs on the lathe, then wiring and debugging
CostNot stated; he didn't say what the whole conversion cost
SafetyRotating machinery, sharp swarf and abrasive cutting that throws sparks and grit, so wear eye protection. Under CNC control the mill moves on its own, and open-loop steppers can skip steps without the machine knowing; keep hands clear while it runs.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Turn a cheap mini mill into a CNC machine

The whole build is in this one video; there is no written guide.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video (This is the only documentation — pause and rewind as you go.)
  2. 2.Note the control setup(He used FluidNC on an ESP32 with open-loop steppers; the video skips the wiring and config files.)
  3. 3.Understand the ball screw swap(He swapped the lead screws for ball screws to cut backlash, trimmed the ball nut flanges and added a Z screw; the cheap imported ones still left about four thousandths of backlash.)
  4. 4.Machine the mounting plates(You will need a mill and lathe to replicate the brackets shown in the video.)

KNOWN ISSUES

  • He made the mounting plates and standoffs himself with a band saw, mill and lathe; without those tools you need another way to make the parts.
  • No written guide, parts list or CAD files are published; the video is the only documentation, so you will be working from the footage and your own measurements.
  • Cheap imported ball screws still left about four thousandths of an inch of backlash in this build, which he thinks caused a small flat spot on the test circle.
  • The ball screws are hardened, so milling them didn't work and he had to trim them with abrasives. Taking the ball nut off can also spill its ball bearings; he lost a couple despite a 3D-printed tube meant to hold them.
  • The first test didn't move at all. He checked continuity, GPIO pins, voltage and whether the motor drivers accept 3.3 V logic from the ESP32 before finding a wiring mistake.
  • The steppers are open-loop, so there is no position feedback — if a motor stalls or skips steps, the machine will not know.

Is there a written guide or BOM?

No. This is a video build log only; no written guide, CAD files or parts list are published.

What mini mill did he use?

A mini mill he had bought a few months before the video. The video does not name the exact model.

How much does the conversion cost?

He didn't say what the whole conversion cost. For comparison, an entry Tormach PCNC 440 benchtop CNC mill starts at 6,890 dollars.

How accurate is it?

The square test section came out about two thousandths of an inch undersize and square. About four thousandths of backlash is left, which he thinks caused a small flat spot on the interpolated circle. He calls it acceptable for his shop.

Can I do this without a mill and lathe?

Not the way he did it. He machined the mounting plates and standoffs himself on his mill and lathe, so you would need those tools or another way to make the parts.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

About four thousandths of an inch of backlash was left from the cheap ball screws, yet the test part came out square and about two thousandths undersize. What would you use this for first?

CompareeTEAM24d ago

Practical notes from our verification: this is a single-video project with no written guide, parts list or CAD to download, so you are working from the footage and your own measurements. The creator does not state what the whole conversion cost, and he made the brackets and standoffs on his own band saw, mill and lathe. The control side is FluidNC on an ESP32 with open-loop steppers, so there is no position feedback. The honest limitation is the cheap imported ball screws: about four thousandths of backlash is left, yet his test part still came out square and about two thousandths undersize.

Someone Should Make That

Someone Should Make That is a YouTube maker who documents his builds on his channel. He started this conversion while looking at digital readouts online: they seemed expensive, and he bet he could make a CNC mill for around the same price.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.