TURN SURPLUS ICE MAKER PARTS INTO A BATTERY-POWERED AIR CONDITIONER

A miniature AC that runs on LiPo packs and uses real refrigerant, not a Peltier chip.

by Hyperspace Pirate

WorkshopEnergy

difficulty
●●●●●
time
a long weekend
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Hyperspace Pirate built a portable air conditioner that uses a real vapor-compression cycle powered by two 4-cell LiPo batteries in series (about 32 V, 70.4 Wh). It draws about 42 watts, weighs about 3.1 kilograms, and in an open-air test with the fan off it started icing up the evaporator coil in under a minute. With the fan running, a thermocouple in front of the coil read 12.7 °C, and he describes it as comparable to a car AC on low to medium. His measured COP is about 1.0. The build is clever, but this is a YouTube demonstration, not a project with files you can download. You would need to salvage coils from tabletop ice makers, braze a refrigerant loop from 1/4 inch copper tubing with a filter dryer and capillary tube, charge it with about 10 grams of propane (R290), drive a three-phase brushless compressor from a speed controller, and design your own 3D printed enclosure. The video does not provide STLs, a wiring diagram, or a parts list. The hardest and riskiest part is brazing and charging the loop: propane is highly flammable, and the compressor is labeled for R134, which runs at lower pressure than propane. If you have never brazed copper or worked with refrigerants, this should not be your first project. It will not cool a room; it is meant to blow cold air directly at you.

GOOD TO KNOW

  • —This is a YouTube build walkthrough, not a repository. There is no CAD, no bill of materials, no step file, no code.
  • —The video shows the build process and explains the refrigerant loop, but you will need to source your own ice makers and adapt the design.
  • —No formal documentation exists. The build requires brazing copper tubing and handling propane refrigerant, both of which require skills not taught in the video.
  • —The condenser and evaporator coils come from surplus tabletop ice makers, which means availability depends on what you can find locally or secondhand.
  • —There is no licence because there is no repository. This is a demonstration, not a reproducible design file set.

Parts to buy

12 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Tabletop ice makers to salvage the coils and capillary tubeFind
  • Small three-phase brushless rotary compressorFind
  • Filter dryerFind
  • 1/4 inch copper tubingFind
  • Servicing valveFind
  • Propane R290 (about 10 g)Find
  • Two 4-cell 2200 mAh LiPo batteriesFind
  • General-purpose three-phase motor controllerFind
  • Buck converterFind
  • Two fansFind
  • Power meterFind
  • Power switchFind

Can I build this?

Print3D printed ABS enclosure panels. The video doesn't share STL files or panel dimensions.
BuyTabletop ice makers to salvage the coils and capillary tube, a small three-phase brushless rotary compressor, filter dryer, 1/4 inch copper tubing, servicing valve, propane R290 (about 10 g), two 4-cell 2200 mAh LiPo batteries, general-purpose three-phase motor controller, buck converter, two fans, power meter, power switch, potentiometer, XT60 connectors
ToolsBrazing torch, refrigerant pressure gauges, servicing valve, soldering iron, 3D printer, LiPo balance charger
SkillsBrazing copper tubing, refrigerant handling, LiPo battery safety, 3D modeling to recreate the enclosure
Timea long weekend if you have brazing experience and the coils already sourced, longer if you are learning refrigerant work or hunting for surplus ice makers
Cost$$, dominated by the compressor, batteries, and refrigerant tools if you do not already own gauges and a way to evacuate the loop
SafetyPropane (R290) is highly flammable: no flames, sparks, or brazing near a charged loop, work with strong ventilation, and leak-test before charging. The compressor in the video is labeled for R134, and propane runs at higher pressure. LiPo batteries need a balance charger and fireproof storage. Brazing involves an open flame. Do not attempt refrigerant work without experience.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Battery-powered air conditioner build

The video is sponsored by boot.dev. The build walkthrough shows the refrigerant loop assembly, the ice maker coil extraction, and thermal performance, but does not provide files or a complete parts list.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the YouTube video to understand the refrigerant loop and component layout (The video is the only documentation. Take notes on the coil placement and brazing joints.)
  2. 2.Source surplus tabletop ice makers for the condenser and evaporator coils(The builder found them at a surplus sale. Check eBay, Craigslist, or local appliance recyclers.)
  3. 3.Design or adapt the 3D printed ABS enclosure to fit your coils and compressor(No STL files are provided. You will need to measure your components and model the panels yourself.)
  4. 4.Braze the refrigerant loop, leak-test it, and charge it with about 10 grams of propane R290(This requires brazing skills and refrigerant gauges. Propane is highly flammable: work outdoors or with strong ventilation, away from any flame or spark, and never braze once refrigerant is in the loop. If you have never done this, find a mentor or take an HVAC course first.)

KNOWN ISSUES

  • There are no STL files, no wiring diagram, and no bill of materials. You are reverse-engineering from a video.
  • The condenser and evaporator coils come from surplus ice makers, which means you cannot buy a fixed part number. You will need to adapt the design to whatever you find.
  • Brazing the refrigerant loop is not beginner-friendly. A leak will vent the propane and the system will not cool. He found a slow leak at a gauge by pressurizing the loop and putting it underwater, so leak-test before charging. Practice on scrap copper first.
  • Propane (R290) is highly flammable. A leak near a flame, spark, or hot surface is a fire risk, and the brazing torch itself is an ignition source, so never braze a loop that contains refrigerant. Work outdoors or in a well-ventilated space, keep the charge small (he used about 10 grams), and keep a fire extinguisher nearby. The compressor in the video is labeled for R134, and propane runs at higher pressure, so a compressor not rated for R290 may be overloaded.
  • The battery runtime is not stated in the video. At about 42 watts and 70.4 watt-hours nominal, the theoretical maximum is roughly 1.7 hours, and less in practice because LiPo packs should not be run completely flat.
  • This will not cool a room. It is designed to blow cold air directly at you, like a personal desk fan.

Can I use a different refrigerant?

The compressor is labeled for R134. Hyperspace Pirate planned to use butane (R600), but his order was lost, so he charged about 10 grams of propane (R290) from a torch bottle. Propane runs at a higher pressure than R134 (about 9.5 bar vs 6.7 bar at room temperature), so he notes the compressor may be a little overloaded, although it ran stable in his tests. Propane and butane are both highly flammable. Never mix refrigerants.

Where do I find a brushless DC compressor?

The video does not name the model. He bought a small rotary (rolling piston) refrigeration compressor with a three-phase brushless motor on eBay a few years earlier. An RC plane ESC could not spin it, so he used a general-purpose three-phase motor controller from Amazon, which the vendor rates at a maximum of 36 V.

Can I skip the vacuum pump and just charge it?

No. Air and moisture in the loop will reduce cooling performance and can freeze at the expansion point, blocking flow. A proper evacuation is not optional.

How long does the battery last?

The video does not say. Two 4-cell 2200 mAh packs give 70.4 Wh nominal; at about 42 W that is roughly 1.7 hours in theory. Real runtime will be shorter, because you should not run LiPo packs completely flat and the draw rises if the compressor runs faster.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

At about 42 watts and 70.4 watt-hours, you get well under two hours of cooling per charge. Would you build this for camping or a car, or is the brazing work and propane handling not worth it for that short a window?

CompareeTEAM29d ago

Practical notes from our verification: this is a YouTube demonstration, not a repository, so there are no files to download. The video shows the build clearly, but you will need to design your own enclosure and salvage your own ice maker coils. The hardest part is not the 3D printing or the wiring; it is brazing the refrigerant loop without leaks and charging it safely with flammable propane. Note that an RC plane ESC could not start the compressor, so he switched to a general-purpose three-phase controller. The video has a sponsor (boot.dev). His measured COP of about 1.0 already accounts for heat lost through the walls of his test box.

Hyperspace Pirate

Hyperspace Pirate is a YouTube creator who builds refrigeration and other physics-heavy projects. This battery-powered air conditioner uses coils salvaged from tabletop ice makers he bought cheap at a surplus sale and a real refrigerant loop, not a Peltier chip.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.