TURN YOUR CAR'S ALTERNATOR INTO A WELDER THAT RIDES UNDER THE HOOD

A modified AD244 alternator charges your battery 99 percent of the time and turns into an emergency welder with the flip of a switch.

by Sweeney Off-Road

Workshop

difficulty
●●●●●
time
a few weeks (the creator's own build)
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a genuine trail-repair hack that a professional welder tested on camera, but it is not a beginner project. You pull the internal bridge rectifier and voltage regulator out of an AD244 alternator, fit an external 200 amp rectifier with a heat sink, add an external voltage regulator from an old Ford (a GM one did not work, per the video), and wire a DPDT switch and a constant duty solenoid so you can toggle between charge mode and weld mode. In weld mode the brush gets a full unregulated 12 volts, and with the engine held at about 1500 rpm the output climbs past 40 volts. Randall Moody of Moody's Metal Works ran a bead with it and called it a solid weld with good penetration that would absolutely work for a trail repair. The creator built it for emergency trail repairs and says it is very dangerous and not to try it at home. The single biggest trap is assuming this is a drop-in mod: he went through a few alternators, burned up the internal regulator on a DPDT circuit, and had to find a regulator that worked. If you already understand alternator internals and have a real use for trail welding, this is a clever solution. If you are learning automotive electrics as you go, pick a different project.

GOOD TO KNOW

  • —No repository exists — this is a documented build from a single YouTube video.
  • —The video walks through the build step by step on camera, but there are no written instructions.
  • —Parts list is in the video description: external rectifier (27 USD), constant duty solenoid (20 USD), DPDT switch (9 USD), heat sink, 2 AWG jumper cables.
  • —The creator explicitly says 'do not try this at home' in the video description.
  • —No CAD files, no schematics, no firmware — the documentation is the video walkthrough and the parts shown on camera.

Parts to buy

7 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • AD244 alternator (if not already installed)Find
  • External 200 amp rectifier27 USDFind
  • Constant duty solenoid20 USDFind
  • DPDT switch9 USDFind
  • Heat sinkFind
  • 2 AWG jumper cablesFind
  • External voltage regulator from an old FordFind

Can I build this?

Printnothing required
BuyAD244 alternator (if not already installed), external 200 amp rectifier (27 USD), constant duty solenoid (20 USD), DPDT switch (9 USD), heat sink, 2 AWG jumper cables, external voltage regulator from an old Ford
ToolsMultimeter, impact wrench for the pulley nut, wire cutters, crimp terminals and heat shrink for the stator leads, thermal paste for the rectifier heat sink, an inline fuse, and a cable-actuated hand throttle to hold engine rpm while welding. Plus the skills to remove and reinstall an alternator.
Skillsadvanced automotive electrical work — you need to understand alternator internals, voltage regulation, and high-current DC wiring; not a beginner project
TimeThe creator worked on it over a few weeks and went through a few alternators along the way. The video gives no time estimate for a repeat build.
Cost$$: the priced parts in the description add up to about 56 USD (external rectifier 27, constant duty solenoid 20, DPDT switch 9), plus a heat sink, 2 AWG jumper cables and an external Ford regulator, which are not priced. The AD244 alternator is extra if you need one. For comparison, a gas engine-drive welder like the Miller Bobcat 265 lists at about 7,315 USD.
SafetyIn weld mode the brush gets a full unregulated 12 volts and the output climbs past 40 volts at around 1500 rpm, feeding welding leads through a 200 amp rectifier. Risk of shorts, burns and damage to the alternator or vehicle electrics if wired incorrectly. The creator says it is very dangerous and not to try it at home. Only attempt if you already work on automotive electrical systems.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

How to Modify an Alternator for Charging AND Welding

1 April 2023. The complete build walkthrough: internal rectifier removal, external rectifier install, regulator swap, switch wiring, voltage test at 1500 rpm, and the professional welder's validation.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video (The only documentation is the video, so watch it start to finish before buying parts. The creator burned up the internal regulator on a DPDT circuit and a GM external regulator did not work, so pay close attention to the regulator and switch wiring sections.)
  2. 2.Source the external regulator(The creator tried a GM regulator and it did not work; he used one from an old Ford. You may need to test or source a specific regulator model.)
  3. 3.Verify your alternator is an AD244 or compatible(The mod is demonstrated on an AD244. Other alternators may have different internal layouts or thermal limits.)

KNOWN ISSUES

  • The biggest mistake is assuming this is a simple switch install. You remove the internal bridge rectifier and regulator, the creator burned up the internal regulator when he tried running it on a DPDT circuit, and a GM external regulator did not work. Budget time to source and test an external regulator (he used one from an old Ford).
  • The creator says it is very dangerous and not to try it at home. In weld mode the brush gets a full unregulated 12 volts and the output climbs past 40 volts, so a wiring mistake on this circuit is not a small problem.
  • The video is the only documentation: there is no written guide or schematic. The description lists the main parts, and the creator explains the switch circuit and terminals on camera so you can troubleshoot it yourself.
  • The stock internal bridge rectifier overheated under welding loads, which is why it was removed. The creator could not desolder the stator leads even with a butane torch, so he cut them, added terminals and heat shrink, and clocked the rear case so the external rectifier clears the engine.
  • The creator built it as an emergency trail welder and says he had never really stick welded before. The clean bead in the video was run by a professional welder, not by him.
  • If you add the 110 V outlet for old brushed power tools, the creator corrects himself on camera: wire it to the welding lead or the rectifier positive output, not to the positive brush.

Can I use this on any alternator?

The build is demonstrated on an AD244 alternator. Other alternators may have different internal layouts, different rectifier configurations, or different thermal limits. The video does not cover other models.

Why did the GM regulator not work?

The video states the GM regulator did not work and the creator switched to a Ford regulator, but does not explain why. This is one of the traps: you may need to test regulators or source a specific model.

How much welding can it do before overheating?

The video does not state a duty cycle or continuous run time. It shows a voltage test and one bead run by a professional welder, and the creator built it as an emergency trail welder. The internal rectifier overheating under welding loads is the reason he moved to an external 200 amp rectifier with a heat sink.

Is this safe for the vehicle?

The creator says it is very dangerous and not to try it at home. In weld mode the brush gets a full unregulated 12 volts and the output climbed past 40 volts at around 1500 rpm in the test. He went through a few alternators and burned up the internal regulator while developing it, so only attempt this if you already work on automotive electrical systems.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

A professional welder called it a solid weld with good penetration, and the priced parts come to about 56 dollars, but the creator says it is very dangerous and not to try it at home. If you had the electrical skills, would you build it for trail repairs or just carry a portable welder?

CompareeTEAM28d ago

Practical notes from our verification: the only source is the single YouTube video from 1 April 2023. There is no repository, no written guide and no schematic. The creator shows the internal rectifier removal and the external rectifier install on camera, and states plainly that a GM regulator did not work and he switched to one from an old Ford (7:47 to 7:55 in the video). The professional welder test (Randall Moody at 18:41 to 18:50) is genuine and on camera. The creator says it is very dangerous and not to try it at home. The biggest surprise is that this is not a drop-in mod: he went through a few alternators and burned up a regulator before it worked, so expect to debug regulator compatibility and the switch wiring.

Sweeney Off-Road

Sweeney Off-Road says this project had intimidated him for a long time before he finally jumped in and brute-forced his way through it. He wanted one alternator that both charges the battery and works as an emergency trail welder, because most guides online turn an alternator into a standalone welder that no longer charges. He went through a few alternators along the way because the internal bridge rectifier kept overheating.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.