TURN A BROKEN TREADMILL INTO A 3D PRINTER THAT PRINTS A WHOLE KAYAK

A broken treadmill becomes a belt printer that prints a kayak in one piece.

by Jon Schone (Proper Printing) and Ivan Miranda

Workshop3D printing

Built with3D printing

difficulty
●●●●●
time
weeks
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Jon Schone and Ivan Miranda turned a dead treadmill into a belt 3D printer and printed a racing kayak in one piece under a nine-day deadline for Maker Faire Prague. The treadmill belt acts as a moving print bed, so the printer can run continuously and print very long parts, and the kayak is as wide as the printer allows. A Duet 3 board runs it from the original treadmill console, and the heated bed is floor heating wire under an aluminum plate. The kayak was planned as a two-seater; to make the deadline the front was redesigned mid-print, with the infill cut to 1%. It floated and stayed in one piece at the faire, but after more abuse it cracked from water in the infill and a layer shift. This is a video-documented build, not a repository: there is no BOM, no assembly guide, no firmware config and no files for the printer itself. The kayak model is on Proper Printing's site, but the printer is learn-by-watching. If you have built printers before, can cut, weld and design your own mounts, and can configure a Duet from scratch, this shows that a belt printer does not have to cost what a roughly 10,000 dollars professional machine does. If you need files and a parts list before you start, this is not for you. Expect the mechanical work to be the hard part: in the video the frame had to be cut and re-welded, the belt replaced, and the motor mount and pulleys designed from scratch.

GOOD TO KNOW

  • —This is a documented build from two YouTube videos, not a repository with files you can download.
  • —The kayak model is available at properprinting.pro, but the printer build itself has no CAD, BOM, wiring diagrams or firmware in a single place.
  • —You are reverse-engineering from video walkthroughs: the first video covers the treadmill conversion, the second covers printing and testing the kayak.
  • —A Duet 3 board controls it. The video doesn't share its configuration files.
  • —The heated bed uses floor heating wire under an aluminum plate; the wiring is not documented as files.
  • —No stated licence; this is a maker documentation project, not an open-source release.

Parts to buy

11 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Treadmill (theirs was broken)Find
  • Replacement beltFind
  • Duet 3 boardFind
  • Stepper motor for the belt with timing beltsFind
  • Power supplyFind
  • Solid state relayFind
  • Floor heating wireFind
  • Aluminum plateFind
  • Linear railsFind
  • Hotend and extruderFind
  • Steel box section and hardware for the frameFind

Can I build this?

PrintNo printable files are published for the printer. In the video they designed and printed their own motor bracket, pulleys (polycarbonate) and power supply bracket (ASA) to fit their treadmill. The kayak model is on properprinting.pro.
BuyA treadmill (theirs was broken), a replacement belt, a Duet 3 board, a stepper motor for the belt with timing belts, a power supply, a solid state relay, floor heating wire, an aluminum plate, linear rails, a hotend and extruder, and steel box section and hardware for the frame.
ToolsA saw and drill, a welder (they used TIG and MIG) and a grinder for the frame, rivet nuts, a soldering iron and multimeter, and a 3D printer for the brackets and pulleys. They also milled the heated bed on a CNC.
SkillsAdvanced: you are building a custom 3D printer from scratch using a treadmill as the base, configuring Duet firmware without a reference config, and solving mechanical alignment with no step-by-step guide. Expect to iterate.
TimeWeeks. In the video the conversion took more than a week of full-time work by two makers and a helper in an equipped workshop, and the kayak then printed for several days.
CostThe video gives no total cost. You need a treadmill, a Duet 3 board, motors, linear rails, a hotend and extruder, heating wire and an aluminum plate. For comparison, a professional belt printer (BlackBelt) was about 10,000 USD in 2019.
SafetyThe heated bed is floor heating wire switched by a solid state relay, and a badly wired heater is a shock and fire risk. Welding and cutting the frame need the usual eye and hand protection. The moving belt and gantry can pinch fingers, so keep clear while it prints.

This build involves mains voltage — for adults comfortable with electrical work only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Build part 1: treadmill to belt printer

The primary build video: covers converting the treadmill into a belt printer, installing the Duet 3, and building the heated bed.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full build video to understand the mechanical conversion(There is no written guide — this video is your documentation. Take notes on every mount, every wire, every firmware setting they mention.)
  2. 2.Source a treadmill(The one in the video was a treadmill that no longer worked, donated by another maker. Check the belt and the frame: the belt becomes your print surface, and theirs had to be replaced.)
  3. 3.Plan your gantry attachment(You are mounting linear rails and a print head to a treadmill frame. The video shows their solution, but your treadmill will be different. Sketch it first.)
  4. 4.Wire the heated bed safely(The bed is floor heating wire under an aluminum plate, switched by a solid state relay. The video does not show the wiring in detail. Use proper strain relief, grounding and a thermal cutoff, and if you are not confident wiring heaters, get someone qualified to do it.)

KNOWN ISSUES

  • You are buying hardware with no parts list. The video shows a Duet 3 and floor heating wire, but does not list suppliers, part numbers, or quantities. Budget extra time for sourcing.
  • Treadmills vary in frame and belt. Even the donated one in the video needed a new belt, a new motor mount and pulleys, and a cut-down, re-welded frame.
  • The heated bed is floor heating wire under an aluminum plate, switched by a solid state relay. The video does not document the wiring or voltage. If you have never wired a heater safely, get help: a badly wired heater is a shock and fire risk.
  • There is no Duet 3 configuration file provided. You are writing your own firmware config from scratch, including belt movement, temperature control, and print head offsets.
  • The kayak print needed solvent sealing to stay watertight and still cracked after further abuse. Printing watertight hollow objects on a belt printer is harder than it looks — expect post-processing.
  • This was built by two experienced makers plus a helper in a workshop with welding and CNC tools, with Prusa supplying filament and a hard deadline. Without that shop and help, expect it to take much longer.

Is there a BOM or parts list?

No. The video shows what they used — a Duet 3, floor heating wire, an aluminum bed plate, a treadmill — but does not list part numbers or quantities. You are sourcing everything yourself.

Can I print the kayak without building the printer?

The kayak model is on properprinting.pro, but it was designed for the treadmill belt printer: its width is based on the maximum width that printer can reach, and it is far longer than the build area of a normal printer.

How much filament did the kayak take?

The video does not state a filament weight or total print time. The print ran for several days against a nine-day deadline, and they cut the infill to 1% to finish in time.

Is the Duet 3 required, or can I use a different board?

The video uses a Duet 3, which can deliver enough current for the motors. Their configuration is not published, so whatever board you use, you write your own config.

Did the kayak actually work?

It floated and stayed intact at Maker Faire Prague after a 1,800 km drive. After further testing it cracked from water in the infill and a layer shift. It worked, but printing large watertight hollow objects is hard.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

If you built a belt printer, what would you print that a normal printer cannot?

CompareeTEAM29d ago

Practical notes from our verification: this is a video-documented build, not a repository. The two YouTube videos (build and kayak test) are your only documentation: there is no BOM, no files for the printer itself, no wiring diagram and no Duet config. The kayak model is on Proper Printing's site, but the printer is what you came to build, and that is a watch-and-figure-it-out project. The heated bed is floor heating wire under aluminum, so take the heater wiring seriously if you have not done it before. If you can reverse-engineer a mechanical system from video and make your own brackets and mounts, this is proof that a belt printer does not have to cost five figures. If you need files before you start, this will frustrate you: the documentation is inspiration, not instruction.

Jon Schone (Proper Printing) and Ivan Miranda

Jon Schone runs Proper Printing. He teamed up with Ivan Miranda, who had already built several huge printers, at Ivan's workshop in Spain. Marcus from Marcus Mechatronics donated a treadmill that no longer worked, they turned it into a belt printer, printed a kayak on it and drove it 1,800 km to Maker Faire Prague to test it on the water.

Web

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.