TURN A 150 DOLLAR PRESSURE WASHER INTO A WATERJET CUTTER THAT CUTS METAL
A 150 dollar pressure washer becomes an abrasive waterjet that cuts aluminum at 2 inches per minute.
by Ben Krasnow
- difficulty
- ●●●●●
- time
- several weekends
- license
- license not specified
- repo
- repo FINISHED
●●●●● · several weekends · license not specified · repo FINISHED
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
Ben Krasnow turned a Sun Joe SPX3000 pressure washer into an abrasive waterjet by turning a copper copy of the brass valve piece with a larger internal diameter, adding spring bias to push the pump from 2000 PSI to about 3200 PSI, shorting the pressure cutout switch, and adding a cooling fan. The water goes through a 12 dollar ruby orifice with an 18 thousandths of an inch hole, then into a tungsten carbide mixing tube where 80 grit garnet falls in from a gravity-fed bucket. It cuts 1/16 inch aluminum at about 2 inches per minute, 1/8 inch aluminum at half that, and 3/8 inch hardwood. This is for someone who can work on a lathe, accepts a pump that now draws 20 to 21 amps on a 20 amp circuit, and is comfortable running a machine that sprang a leak at 3500 PSI and sits in a tub of water. There are no files, no drawings, no step list. You watch the video and make your own decisions. The one thing most likely to go wrong is the valve: Ben shows that the stock plunger slams open and makes the pump oscillate, and his copper part with a larger bore is what fixes it. This is a demonstration of what is possible, not a weekend project.
IN THE REPO
GOOD TO KNOW
- —There is no repository. The project is a single Applied Science YouTube video from May 2017, about 21 minutes long.
- —No CAD files, no drawings, no step-by-step guide. You watch the video, pause it, and machine the parts yourself.
- —The valve modification needs a lathe: Ben turned a copper copy of the brass valve piece with a larger internal diameter.
- —No BOM list on the page. Ben names the pressure washer (Sun Joe SPX3000), the cutting head supplier (AccuStream) and the abrasive (80 grit garnet), and says links to where he bought the parts are in the video description.
- —The video is very detailed on the physics and the problems, but it is a demonstration build, not a released design.
- —No licence is stated. This is a YouTube project, not a released design.
Parts to buy
8 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
Can I build this?
This build involves mains voltage — for adults comfortable with electrical work only.
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
Building an abrasive waterjet cutter with a $150 pressure washer21:00
The entire project in one video, about 21 minutes. 3.7 million views.
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Watch the YouTube video twice. Once to understand what Ben is doing, once to take notes on the valve modification, the pressure settings and the cutting head parts.
- 2.Buy the Sun Joe SPX3000 pressure washer. It is the base of the entire build.
- 3.Buy the ruby orifice and tungsten carbide mixing tube. Ben bought his from AccuStream and links his sources in the video description.(18 thousandths of an inch orifice, 40 thousandths of an inch mixing tube)
- 4.Machine the copper relief valve part. This is the hardest step and the one that determines whether the build works.
KNOWN ISSUES
- The valve is the core of the project. The stock plunger fits snugly enough to create positive feedback, so the valve slams open and the pump oscillates. Ben fixed this by turning a copper copy of the brass piece with a larger internal diameter so the plunger fits loose. Without a lathe you cannot make that part.
- The motor draws 20 to 21 amps at 120 volts after the modification. A 20 amp circuit will trip. Ben ran test cuts for only a few minutes at a time. You need a way to handle the current or accept very short duty cycles.
- At 3500 PSI the machine sprang a leak, so it sits in a tub of water. Ben says 3200 PSI is a good pressure for this system because the hose is rated for 2900 PSI working pressure. Do not push it higher.
- The cutting head is a commercial AccuStream part, not something you machine. The orifice and mixing tube have to be precise and concentric. Tungsten carbide is brittle: Ben broke a mixing tube by dropping it while clearing a clog in a 30 thou nozzle.
- Abrasive consumption is about 0.4 pounds of 80 grit garnet per minute. If the mixing tube clogs, water can back up into the hopper, and wet sand clumps and stops flowing. Ben calls getting water in your sand one of the worst things ever.
- This is hand-guided. There is no CNC, no bed, no guides. You hold the cutting head and move it. Straight lines and repeatable cuts are hard.
Can I use a different pressure washer?
Maybe, but the video only covers the Sun Joe SPX3000, a 150 dollar electric washer rated 2000 PSI at 1.7 gallons per minute and one of the most popular on Amazon. Its stock valve combines a relief valve, an unloader valve and a motor control valve in one plastic plunger, and the modification is specific to that design. Another washer would need its own valve work, so starting with the same model is the safest choice.
Where do I buy the ruby orifice and mixing tube?
Ben bought the cutting head parts from AccuStream and says he put links to where he bought everything in the video description. He used a ruby orifice with an 18 thousandths of an inch hole (about 12 dollars) and a tungsten carbide mixing tube with a 40 thousandths of an inch bore, about 3 inches long (about 80 dollars). He chose 18 thou so the pump draws about 20 amps at its flow rate; the size is matched to this pump.
How fast does it cut compared to a commercial waterjet?
Much slower. About 2 inches per minute in 1/16 inch aluminum and about 1 inch per minute in 1/8 inch aluminum. Ben says a commercial machine is much faster, but for hobby projects at home production speed is not a big issue. A commercial waterjet might cost 150,000 dollars; the WAZER desktop waterjet lists at 9,999 dollars.
Is there a forum or community for this build?
The project lives in the Applied Science video from May 2017. The best place to ask questions about this build is the comments under that video.
Can I cut steel?
Ben does not show steel cuts in the video. He cuts 1/16 and 1/8 inch aluminum, 3/8 inch hardwood, and in water-only mode foam and bread.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
The motor pulls 20 to 21 amps on a 20 amp circuit, so Ben could only run it for a few minutes at a time. If you were building this, would you try to derate the pressure to stay within 20 amps, or would you run it on a higher-rated circuit?
Ben Krasnow
Ben Krasnow runs the Applied Science YouTube channel. In this video he builds an abrasive waterjet cutter from a 150 dollar pressure washer and explains the physics behind it, from the valve modification to why the abrasive particles act like tiny bullets.
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM29d ago
Practical notes from our verification: there is no repository and no file pack. The project is one Applied Science video from May 2017, about 21 minutes long, with parts links in its description. The video is very detailed on the physics and the problems, but it is a demonstration, not a released design. The single biggest decision is whether you can turn the copper valve part on a lathe. If you cannot, the build stops there. The second biggest decision is whether you can live with a machine that draws beyond the circuit rating and sprang a leak at 3500 PSI. Ben is very clear about the limitations: it is hand-guided, it only ran for a few minutes at a time, and a commercial machine is much faster. This is a proof of concept, not a production tool.