TURN AN OLD OVEN INTO A KILN THAT TURNS 3D PRINTS INTO ALUMINUM PARTS

A 40 dollar kitchen oven lined with fire bricks and wired to a cheap eBay controller turns 3D prints into aluminum castings.

by TheBackyardScientist

Workshop

difficulty
●●●●○
time
Not stated; burnout alone takes 18 hours
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a video of a build, not a set of plans. TheBackyardScientist converted a 40 dollar kitchen oven into a burnout kiln that reaches about 786°C, hot enough to burn plastic out of plaster molds so molten aluminum can be poured in. The castings came out smooth and picked up the detail of the 3D prints. The whole build cost about 270 dollars, while a Paragon TNFJ141 burnout kiln costs 2,695 and goes hotter, up to 927°C. He says the materials matter more than how his particular oven was taken apart, so you learn the approach, not a parts list. Take the risks seriously: a 786°C oven and molten aluminum mean severe burns and fire, and moisture left in a mold can make the metal blow out explosively. The ceramic fiber needs long sleeves, a respirator and a sealant. The old oven insulation may contain asbestos, so do not strip an old oven yourself. The controller and heating elements run on mains voltage, so leave that wiring to a qualified electrician. If you already cast metal, this is a practical kiln upgrade. If you have never handled molten aluminum, the oven is the least of what you need to learn.

GOOD TO KNOW

  • —This is a YouTube walkthrough (lMi1P-J-nmY), not a repository with downloadable files.
  • —There is no written parts list, no CAD, no wiring diagram, and no step-by-step build document.
  • —The video shows the entire process with timestamps: removing old insulation (00:22), laying fire bricks and ceramic blanket (00:22-01:47), wiring the controller (02:07), and the full casting cycle (05:15-05:57).
  • —No plans or licence are published. This is a video of one person's build.
  • —The creator warns the old oven insulation may have been asbestos and that ceramic fiber needs sealing and long sleeves.

Parts to buy

8 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Used kitchen ovenFind
  • 10 insulating fire bricksabout 3 USD eachFind
  • High temperature mortarFind
  • Biosoluble ceramic fiber blanketFind
  • Sealant for the fiberFind
  • EBay digital temperature controller kit with relay and thermocoupleFind
  • Plaster for moldsFind
  • Scrap aluminum for castingFind

Can I build this?

Printnothing required for the kiln; 3D printed PLA parts become the patterns for the castings
Buyused kitchen oven, 10 insulating fire bricks (about 3 USD each), high temperature mortar, biosoluble ceramic fiber blanket, sealant for the fiber (colloidal silica or a thin mortar layer), eBay digital temperature controller kit with relay and thermocouple, plaster for molds, scrap aluminum for casting
Toolstools to take the oven apart, a Dremel to cut the controller hole, a drill for the holes through the bricks, a foundry and crucible for melting aluminum, sand to back the mold, a hammer and hose to remove the plaster; protection: long sleeves and a respirator for the ceramic fiber, heat-resistant gloves and a face shield around molten metal
Skillsexperience melting and pouring aluminum safely, ability to learn from a video without written instructions, awareness of asbestos risk in old appliances; the mains-voltage wiring of the controller and heating elements should be done or checked by a qualified electrician
TimeThe video does not give a build time. The first test reached about 786°C after an hour. Each mold needs a day for the plaster to dry, then about 18 hours of baking (6 hours each at 200, 400 and 600°C), plus foundry time.
Cost$$: the oven was 40 USD and the whole build about 270 USD; plaster and aluminum are extra for each casting
SafetySerious burn and fire risk: the oven reaches about 786°C and the castings use molten aluminum. Moisture in a mold can make the metal blow out explosively, so the plaster must be fully dry. Ceramic fiber needs long sleeves, a respirator and a sealant. Old oven insulation may contain asbestos; do not remove it yourself from an old oven. The controller and elements run on mains voltage; leave that wiring to a qualified electrician. A professional burnout kiln goes hotter, up to 927°C. Not a beginner-safe build.

This build involves mains voltage — for adults comfortable with electrical work only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Old oven to burnout kiln — full build and casting process

The main documentation for this build. No written guide is linked from this page.

More builds like this

All projects

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video at least twice before buying anything (Focus on the materials he chose. He says they matter more than how his specific oven was taken apart, because your oven will likely be different. Leave the mains wiring to a qualified electrician.)
  2. 2.Source a used oven and verify the heating elements still work(The creator says his oven's original insulation was probably asbestos. With an old oven, do not remove the insulation yourself; have it checked by a professional first.)
  3. 3.Buy fire bricks, mortar, ceramic blanket, and the controller before you start tearing the oven apart(He used 10 insulating fire bricks (about 3 USD each), high temperature mortar, a biosoluble ceramic fiber blanket and an eBay controller kit with a relay and thermocouple. Wear long sleeves and a respirator when cutting the fiber.)
  4. 4.Build a small test mold and run the full 18-hour burnout cycle before casting anything you care about(Let the plaster dry for a day first. A damp mold and molten aluminum can blow out violently.)

KNOWN ISSUES

  • Tearing into an old oven yourself. The creator says his oven's original insulation was probably asbestos. With an old oven, do not remove the insulation yourself; have it checked and handled by a professional.
  • Handling the ceramic fiber blanket without long sleeves and a respirator. He found it far itchier than expected, and he says fiber blanket should be sealed with colloidal silica or a thin layer of mortar because moisture degrades it.
  • Wiring the controller and heating elements yourself without the right skills. It is mains voltage, there is no wiring diagram, and a mistake can mean a fire or electric shock. Have a qualified electrician do or check it.
  • Expecting 3D prints to come out as metal. The prints burn away. What you get is a metal casting of the print's shape.
  • Underestimating the 18-hour baking cycle per mold. This is not a same-day process.
  • Pouring molten aluminum without foundry experience or into a mold that is not fully dry. Moisture in the mold can make the metal blow out explosively. Melting and pouring aluminum safely is a separate skill that the video does not teach in detail.

Can I use a different temperature controller?

The video only shows one option: an eBay kit with the controller unit, a relay and a thermocouple, fitted where the old oven knob was. It does not compare other controllers. Whatever you use, this is mains-voltage wiring next to a very hot oven, so have a qualified electrician check it.

How long does the burnout cycle take?

After the plaster dries for a day, the block bakes for 6 hours at 200°C, 6 hours at 400°C and 6 hours at 600°C so the plastic burns out. That is about 18 hours in the oven per mold, before any metal is poured.

Can this oven be used for other metals?

The video only casts aluminum, melted in a separate foundry. The oven's job is burning the plastic out of the plaster mold, and it tops out at about 786°C. A professional burnout kiln goes hotter, up to 927°C. No other metals are tested in the video.

Do I need a 3D printer for this?

The video uses 3D printed parts as the patterns, which is lost PLA casting. He describes the oven as a burnout furnace for wax investments too, but only 3D printed patterns are shown.

How much does the oven cost to run for 18 hours?

The video does not give an energy figure. It only gives the build cost (about 270 USD, with the oven itself at 40 USD) and the bake schedule of 6 hours each at 200, 400 and 600°C per mold.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Would you build this oven kiln for aluminum castings, or save for a professional burnout kiln that goes up to 927°C?

CompareeTEAM24d ago

Practical notes from our verification: there are no written plans, no wiring diagram and no downloadable files on this page. The video is the documentation. The facts we could confirm: a 40 dollar oven, 10 insulating fire bricks at about 3 USD each, high temperature mortar, a biosoluble ceramic fiber blanket, an eBay controller, about 786°C after an hour, and about 270 dollars in total. The biggest mistake is underestimating the danger. Molten aluminum and a 786°C oven mean severe burns and fire, a damp mold can make the metal blow out, the fiber needs sleeves and a respirator, an old oven may hide asbestos, and the mains wiring belongs to a qualified electrician. If you already cast metal, this is a practical kiln upgrade. If you are new to metal casting, the kiln is the least of what you need to learn.

TheBackyardScientist

TheBackyardScientist (@thebackyardscientist_) is a YouTube creator. In this video he turns a 40 dollar kitchen oven into a burnout kiln so he can cast aluminum from 3D printed patterns, and calls it his first attempt at lost PLA casting.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.