BUILD A 200 DOLLAR MACHINE THAT PLACES CHIPS SMALLER THAN A GRAIN OF RICE

A 200-dollar homemade machine that can position parts smaller than a grain of rice, controlled with joysticks instead of code.

by Magmabow

WorkshopOpen-hardware

Built with3D printing

difficulty
●●●●○
time
a long weekend
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a manual pick-and-place machine built around lead screws, lapped 3D-printed herringbone gears and vacuum nozzles. Magmabow estimates it reaches about 10 microns of precision, enough to handle 0201 parts (0.6 by 0.3 mm) up to larger chips. You steer it with two joysticks, place each component by hand, then solder the board on a hot plate. The mainboard came from an old Ultimaker 3D printer he took apart. The parts cost came to around 180 to 195 dollars, a fraction of the 10,000-plus-dollar cost of a desktop machine like the NeoDen 4, which is fully automatic. The printable files are on Printables. The catch: the control code is not published, so you will need to write your own, and his first board overheated on the hot plate. This is a project for someone who already understands steppers and motion control.

GOOD TO KNOW

  • —All STL files are on Printables under CC0 (public domain), so anyone can use them commercially.
  • —The control code is not published. The mainboard came from an old Ultimaker 3D printer with five stepper drivers.
  • —The Printables page has photos and a short description, but no step-by-step assembly guide.
  • —Magmabow estimates the full parts cost at 180 to 195 dollars including printed plastic, but you will have to identify every motor, lead screw, vacuum pump and joystick yourself.
  • —This is a manual machine: you steer each placement with joysticks. It is not automatic and will not compete with a factory line.
  • —The builder's first board overheated on the hot plate during reflow, so the soldering step has real risk of failure.

Parts to buy

7 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Lead screwsFind
  • Stepper motorsFind
  • Vacuum pumpFind
  • Vacuum nozzles (0201 to 0603 range)Find
  • JoysticksFind
  • 3D printer mainboardFind
  • Miscellaneous hardwareFind

Can I build this?

PrintFull set of parts (frame, gears, tool heads, mounts) from the Printables page. Herringbone gears need to be lapped after printing for smooth motion.
BuyLead screws, stepper motors, vacuum pump, vacuum nozzles (0201 to 0603 range), joysticks, 3D printer mainboard, and miscellaneous hardware. No BOM provided, so you will source everything from the video and photos.
Tools3D printer (multiple parts, some precision gears), soldering iron, hot plate for reflow, basic hand tools, and time to configure the mainboard firmware for joystick control.
SkillsHigh. You need experience with 3D printer electronics, stepper motor wiring, firmware configuration, and SMD soldering. No guide exists, so you will be working from photos and one video.
TimeA long weekend if you already know motion control and have all the parts. Longer if you are sourcing blindly or learning as you go.
Cost$$. The builder spent 180 to 195 dollars including filament. Lead screws, steppers, and the vacuum system will dominate the cost.
SafetyHot plate reflow involves temperatures that can damage boards if left too long — the builder's first board overheated. Otherwise, standard electronics and 3D printing precautions apply.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

I Built A Million-Dollar Machine For $200

The primary build video showing the machine in action, the parts cost estimate, and the precision claim. No assembly walkthrough.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Download the STL files from Printables (model 1725186) and watch the YouTube video to see which parts are printed and how they fit together. (The Printables page has the CAD files but no assembly instructions or BOM.)
  2. 2.Identify the motors, lead screws, vacuum pump, nozzles and mainboard from the video stills. You will be reverse-engineering the parts list.(The builder does not publish a parts list, so pause the video and match what you see to available hardware.)
  3. 3.Print the herringbone gears and lap them together until they mesh smoothly. This step determines whether your motion will be precise or jerky.(The builder mentions lapping the gears. Skipping this will give you slop in the motion.)
  4. 4.Set up a 3D printer mainboard for joystick control with your own code.(He reused an old Ultimaker mainboard and wrote his own code, which is not shared.)

Resources

Documentation, files and community threads for this build — we link straight to the original sources and never rehost the creator’s files.

KNOWN ISSUES

  • There is no BOM, so you will spend hours pausing the video to identify motors, lead screws, the vacuum pump, and the mainboard. If you guess wrong, parts will not fit or perform.
  • The mainboard is from an old Ultimaker 3D printer and he wrote his own code for it; the code is not published, so you will set up motor drivers and joystick control yourself.
  • Herringbone gears must be lapped after printing. If you skip this or print them carelessly, the motion will have too much play to place 0201 parts reliably.
  • This is a manual machine: you position every part with joysticks. It will not automate a production run, and it will be slower than any commercial pick-and-place.
  • The builder's first board overheated on the hot plate during reflow. You will need to learn the correct temperature and timing or risk burning the PCB.

Is this faster than placing parts by hand with tweezers?

Not necessarily. It is more precise and less fatiguing for long sessions, but you are still positioning every part manually with joysticks. Speed is not the reason to build this.

Can I use it for boards with hundreds of components?

Technically yes, but it will take a very long time. This is aimed at prototypes or small-batch boards where the precision matters more than throughput.

Which 3D printer mainboard should I use?

He used the mainboard from an old Ultimaker 3D printer he had taken apart, which has five stepper drivers, and wrote his own code for it. That code is not published.

Do I need a vacuum pump or can I use something else?

A vacuum nozzle is the standard way to pick up tiny SMD parts without damaging them. Tweezers can work for larger chips but will struggle with 0201s.

What if I have never soldered with a hot plate before?

Practice on scrap boards first. The builder overheated his first board, so there is a real learning curve to getting the temperature and timing right.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The builder estimates 10 microns of precision from lead screws and lapped printed gears, and the parts cost came to around 190 dollars. If you have built motion systems before, what would you change to make the missing BOM and firmware less of a problem?

CompareeTEAM1mo ago

Practical notes from our verification: the Printables page (model 1725186) has the design files, but the control code is not published. The video shows the machine working and gives the parts cost, but it is not an assembly tutorial. He used the mainboard from an old Ultimaker 3D printer and wrote his own code, so if you have never configured stepper drivers, that gap will stop you. The hot plate step also has real risk: his first board overheated.

Magmabow

Magmabow built this manual pick-and-place to handle surface-mount parts as small as 0201 (0.6 by 0.3 mm) without spending five figures on a commercial machine. The design uses lapped 3D-printed gears and lead screws for slow, precise motion instead of the belts and servos found in factory equipment.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.