TURN A SINGLE LIGHT SENSOR INTO A CAMERA THAT SEES AROUND THINGS

A single photodiode on a spinning arm builds full images and acts like lenses that would be impossible to manufacture.

by Shane Wighton

ScienceWorkshop

difficulty
●●●●●
time
a long project
license
license not specified
repo
repo FINISHED
1
Jump to section

COMPAREE VERDICT

Shane Wighton built a camera that uses one photodiode and motion to replace an entire sensor. A hole in a metal plate lets through one point of light. The sensor sits on a cart that slides along a spinning arm, and it looks at a mirror whose angle the software controls. As the arm spins, the sensor is read about 10,000 times a second and every reading becomes a pixel. Because the software chooses where the sensor sits in space and where it points, the same machine can act like a wide angle lens, a telephoto, or lenses that cannot exist — including ones that see a face from five angles at once, unfolded like a map. The images are rough, black and white unless you make three passes, and Wighton says a cheap camera does better. This is a concept piece, not a weekend build. There are no files, no parts list, no firmware. The video was sponsored by Brilliant and does not explain how to replicate the electronics or the motion control. If you want to understand the idea and see what it produces, the video is worth watching. If you want to build it, you are starting from zero.

GOOD TO KNOW

  • —This is a demonstration project, not a published build.
  • —No CAD files, no BOM, no firmware, no build instructions.
  • —The video explains the concept and shows the result, but does not teach how to make it.
  • —The sensor reads about 10,000 times per second and the software calculates where it should look.
  • —Color requires three separate red, green and blue filtered passes.
  • —The creator states a 2 dollar camera takes sharper pictures.

Parts to buy

8 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • PhotodiodeFind
  • Spinning arm mechanismFind
  • Cart with linear motionFind
  • Mirror with precise angle controlFind
  • MotorFind
  • Electronics for 10from the repo files
  • 000 Hz samplingFind
  • Colored filters for RGB passesFind

Can I build this?

Printnothing required
Buyphotodiode, spinning arm mechanism, cart with linear motion, mirror with precise angle control, motor, electronics for 10,000 Hz sampling, colored filters for RGB passes
Toolscustom motion control software, high-speed data acquisition, mechanical fabrication tools
Skillsadvanced — requires motion control, high-speed sampling, custom software for image synthesis, mechanical precision
Timeseveral weekends, assuming you design everything from scratch
Cost$$$, dominated by precision motion hardware and control electronics
SafetyRotating machinery with exposed moving parts. No mains voltage or lasers mentioned, but the spinning arm and motor require physical guards and care during operation.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

What if we made a camera that sees in reverse?

Posted 4 Dec 2024, 5.97M views. Explains the concept and shows the results. No build instructions. Sponsored by Brilliant.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the video to understand the concept (The video shows what it does and roughly how it works, but does not provide build files or a parts list.)

KNOWN ISSUES

  • There are no build files. If you want to replicate this, you are designing the entire motion control system, the electronics, and the software from scratch.
  • The sensor must be read about 10,000 times per second, which requires fast data acquisition and precise synchronization with the motion.
  • Color images require three separate passes with red, green and blue filters, tripling the capture time.
  • The software must calculate where the sensor should sit and where it should look for every pixel, then stitch 10,000 readings per second into a coherent image.
  • The creator states the image quality is worse than a 2 dollar camera — this is a demonstration of an idea, not a practical alternative to normal cameras.
  • The video was sponsored, so some of the presentation is shaped by that relationship.

Can I build this from the video?

No. The video explains the concept and shows the machine running, but does not provide CAD files, a BOM, firmware, or step-by-step instructions.

How long does it take to capture one image?

The video does not say, but color requires three separate passes with different filters, so it is not instant.

What is the resolution?

The video does not state a pixel count. The creator says a 2 dollar camera takes sharper pictures.

What can this do that a normal camera cannot?

Because the software controls where the sensor sits and where it looks, it can act like lenses that would be impossible to manufacture, including ones that see a face from multiple angles at once.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The sensor reads 10,000 times per second and the software decides where it should look for every pixel. If you were designing the image-stitching algorithm from scratch, what would trip you up first — motion synchronization, or deciding how to map those readings into a coherent picture?

CompareeTEAM1mo ago

Practical notes from our verification: this is a demonstration project, not a published build. The video has 5.97 million views and explains the concept clearly, but provides no files, no BOM, and no firmware. The creator states plainly that a cheap camera takes better pictures. If you want to see what a one-pixel camera can do and understand the idea, the video is excellent. If you want to build it, you are starting with nothing but the concept and a lot of custom engineering ahead of you.

Shane Wighton

Shane Wighton runs the YouTube channel Stuff Made Here, where he builds machines that demonstrate engineering concepts and often do impossible-sounding things. The one-pixel camera is a demonstration project to explore what happens when you replace an entire sensor with a single photodiode and motion.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.