TURN YOUR TV'S 1980S OPTICAL PORT INTO LASER WIRELESS SURROUND SOUND

Replace the LED in a 1980s optical audio port with a low-power laser, and you get wireless surround speakers with zero compression and zero lag.

by Matt (DIY Perks)

AudioHome

Built with3D printing

difficulty
●●●●○
time
a weekend-plus
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a proper speaker build that happens to use lasers instead of cables. TOSLINK (also called SPDIF optical) sends uncompressed digital audio as pulses from a red LED through a plastic fibre. Matt from DIY Perks wired a 3 volt class 1 laser diode to the transmitter's signal pin instead, so the beam travels through the air. Cheap analog-to-SPDIF and SPDIF-to-analog converters handle encoding and decoding, and the centre speaker carries a four-laser distribution block that beams the signal to the other speakers. A strip of HDPE plastic from a bottle widens the receiver target. The speakers themselves are 3D printed enclosures with Dayton TCP115-4 mid-bass drivers, tweeters, acrylic tube transmission lines, amplifiers and a DSP. The surround channels reach 35 Hz without a subwoofer, and Matt says the whole set with new parts costs about the same as a mid-range soundbar. The thing most likely to go wrong is aiming: each laser has to be precisely aligned at its receiver, and anything in the way breaks the link. If you want wireless audio with no Bluetooth lag and you already build speakers, this is a genuinely clever use of old tech. If you have never built speakers before, start with a simpler design first.

GOOD TO KNOW

  • —3D models are paid (payhip.com/b/3oXxU), not open source
  • —Parts list is in the YouTube video description and the build is shown in the 21-minute video
  • —No repository — this is a documented build, not a software or hardware design project
  • —No firmware involved: SPDIF converters and amplifiers are off-the-shelf modules
  • —No PCB files: the electronics are off-the-shelf SPDIF converters, an amplifier and a DSP wired together

Parts to buy

12 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Dayton TCP115-4 mid-bass driversFind
  • TweetersFind
  • Acrylic tubing for transmission linesFind
  • 3 V class 1 laser diodesFind
  • TOSLINK transmitter modulesFind
  • TOSLINK receiver modulesFind
  • Analog-to-SPDIF encoderFind
  • SPDIF-to-analog decodersFind
  • 4-channel amplifierFind
  • DSP moduleFind
  • HDPE plastic (or cut from a bottle)Find
  • Wiring and connectorsFind

Can I build this?

PrintLarge speaker enclosures (paid STL models from payhip.com/b/3oXxU), plus mounts for the laser transmitters and SPDIF receivers
BuyDayton TCP115-4 mid-bass drivers, tweeters, acrylic tubing for transmission lines, 3 V class 1 laser diodes, TOSLINK transmitter modules, TOSLINK receiver modules, analog-to-SPDIF encoder, SPDIF-to-analog decoders, 4-channel amplifier, DSP module, HDPE plastic (or cut from a bottle), wiring and connectors. Full parts list in the YouTube video description.
ToolsLarge-format 3D printer (or access to one), soldering iron, wire strippers, screwdrivers, alignment patience
SkillsSpeaker building experience recommended: you are tuning transmission lines and wiring multi-channel audio. Soldering is straightforward but alignment of each laser to its receiver is fiddly and unforgiving.
TimeA weekend-plus: printing the enclosures alone will take many hours, then assembly, wiring, tuning and precise laser alignment for each channel.
Cost$$: Matt says the full set with new parts costs about the same as a mid-range soundbar, so expect a few hundred dollars (drivers, amplifier, DSP, converters, paid models). The laser diodes and SPDIF modules are cheap; the drivers and amplifier are not.
SafetyLow-power class 1 lasers only — these are the safe kind used in CD players and TOSLINK transmitters. Do not use higher-power laser diodes. Standard soldering and electronics safety apply.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

DIY Surround Sound... USING LASERS!18:00

Full 21-minute build walkthrough from DIY Perks, 13 Dec 2024, 3.16M views. Parts list in the description.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full video (21 minutes, covers the TOSLINK principle, laser wiring, speaker build and tuning)
  2. 2.Buy the 3D models (Paid models for the speaker enclosures and laser/receiver mounts)
  3. 3.Source the parts(Full list in the YouTube video description. Dayton drivers, acrylic tubes, SPDIF converters, class 1 laser diodes, amplifier and DSP.)
  4. 4.Print the enclosures(Large prints — check your bed size or find a print service)
  5. 5.Wire and align(Follow the video for wiring the SPDIF converters and laser modules, then spend time aligning each laser to its receiver)

KNOWN ISSUES

  • The 3D models are paid, not open source — budget for that before you start.
  • Each laser must be aimed precisely at its receiver and cannot move. This is not plug-and-play wireless.
  • You need a 3D printer. The speaker shells are large prints with hollow walls that get filled later, so expect a lot of print time.
  • This is a full speaker build, not a quick electronics mod. If you have never built speakers or tuned transmission lines, expect a learning curve.
  • Only use low-power class 1 laser diodes (the kind in CD players and TOSLINK transmitters). Higher-power lasers are a safety hazard.

Does this work through walls?

No. The laser has to travel in a straight line from transmitter to receiver. Any obstruction breaks the link.

Is there any lag compared to Bluetooth?

None. TOSLINK is uncompressed digital audio with near-zero latency, and the laser does not add any processing delay. This is why it works for surround sound.

Can I use higher-power lasers to increase range?

No. He uses low-power 3 volt class 1 laser diodes, which are low enough power to be considered safe. Higher-power lasers are a real eye hazard.

What happens if someone walks through the beam?

That channel cuts out until the beam is unobstructed again. The laser is safe, but the audio will drop.

Can I use this for Dolby Atmos or 5.1 surround?

TOSLINK carries two-channel uncompressed audio. Matt's build uses separate lasers for each speaker channel (front left, front right, surround left, surround right), not a single multi-channel stream. It is a surround setup, but not a single Dolby 5.1 bitstream.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The surround channels hit 35 Hz without a subwoofer, and the whole system costs about the same as a mid-range soundbar — but you have to aim each laser and keep them aligned. Would you trust this in a living room, or is the alignment too fiddly for daily use?

CompareeTEAM1mo ago

Practical notes from our verification: there is no GitHub repository or open-source release. This is a documented build with paid models, and the only source is the 21-minute YouTube video and its description. The single biggest decision is whether you already build speakers: if you do, this is a genuinely clever use of TOSLINK and low-power lasers; if you do not, the transmission line tuning and multi-channel wiring will be harder than the laser part. The 3D models are paid at payhip.com/b/3oXxU, and the 'about the same as a mid-range soundbar' figure is Matt's own estimate for the set with new parts.

Matt (DIY Perks)

DIY Perks is a YouTube channel known for high-production builds that combine clean fabrication with clever engineering. Matt often works with custom enclosures, passive cooling and audio projects. This build came from noticing that TOSLINK only needs the fibre to guide the light, not to carry it.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.