TURN A 256GB IPHONE DUO INTO A 1TB ONE

DirectorFeng replaced Apple's soldered flash chip by hand and turned a 1,999-dollar iPhone Duo into the 2,599-dollar model.

by DirectorFeng

Open-hardware

difficulty
●●●●●
time
a full day plus practice runs
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is an expert-level microsoldering demonstration, not a weekend project. DirectorFeng heated off the original 256GB BGA flash chip from an iPhone Duo mainboard, cleaned every pad, soldered a 1TB replacement, then restored iOS from a Mac. The phone booted with four times the storage it shipped with. Apple charges 600 dollars to go from 256GB to 1TB, so the price gap is real — but so is the skill gap. You need a BGA rework station, a stereo microscope, flux, solder paste, and the muscle memory to reflow a chip with hundreds of balls without lifting a pad or bridging neighbours. The single most likely mistake is destroying the board on your first attempt, because foldable iPhones have no repair manuals and the margin for error is measured in tenths of a millimetre. The video shows the result, not every step, and it does not name the flash chip supplier. If you have never done BGA work, this is not where you start. If you have, it proves the phone will accept a larger chip — but you are on your own sourcing it and surviving the install.

GOOD TO KNOW

  • —This is a demonstration video, not a build guide with files or a parts list.
  • —No schematic, no pinout, no step-by-step written instructions.
  • —The 1TB flash chip comes from the parts market — DirectorFeng does not say which supplier or model.
  • —Opening a foldable iPhone voids warranty and risks damaging the hinge and display.
  • —Apple does not publish board layouts or chip datasheets, so this is reverse-engineering.
  • —No licence applies — this is a custom modification of a commercial product you own.

Parts to buy

5 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • 1TB NAND flash chip compatible with iPhone DuoFind
  • FluxFind
  • Solder pasteFind
  • Isopropyl alcoholFind
  • Opening tools for foldable iPhonesFind

Can I build this?

Printnothing required
Buy1TB NAND flash chip compatible with iPhone Duo (supplier not named in video), flux, solder paste, isopropyl alcohol, opening tools for foldable iPhones
ToolsBGA rework station, stereo microscope, hot air station, tweezers, Mac running macOS for iOS restore via Finder
SkillsProfessional microsoldering experience — BGA reflow, pad cleaning, component alignment under magnification. This is not a first electronics project.
TimeSeveral hours for an experienced technician, plus practice runs if you have never removed a BGA chip from a live iPhone board before.
Cost$$$, dominated by the rework station if you do not already own one.
SafetyNo mains voltage or lithium fire risk if the battery is disconnected first. Real risk is destroying a $2,000 phone — foldable displays and hinges are fragile, and lifting a pad on the mainboard turns the board into e-waste.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

World First: iPhone Duo 256GB Successfully Upgraded to 1TB

DirectorFeng's full teardown and upgrade. Filmed in real time with close-ups of the soldering work. No English subtitles, but the process is visual.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full DirectorFeng video to see the teardown sequence and soldering technique (This is the only public documentation. There is no written guide.)
  2. 2.Source a compatible 1TB NAND flash chip(DirectorFeng does not name the supplier or part number. You will need to identify the original chip model and find a replacement with matching pinout and protocol.)
  3. 3.Set up your rework station and practice on a donor board first(Do not attempt this on a live $2,000 phone as your first BGA job. The iPhone Duo board is multilayer and the pads are small.)
  4. 4.Disconnect the battery, remove the board, heat off the old chip, clean the pads, align and reflow the new chip(The video shows the technique but does not give temperatures or dwell times. You will need to tune your station for this specific board.)
  5. 5.Reinstall the board, connect to a Mac, and restore iOS via Finder(The phone must be in DFU mode.)

KNOWN ISSUES

  • The video does not name the flash chip model or supplier. Finding a compatible 1TB NAND with the correct pinout and firmware protocol is the first real obstacle.
  • Foldable iPhones are not designed to be opened. The hinge mechanism and the inner display are both at risk every time you separate the halves.
  • BGA chips have hundreds of solder balls. Lifting a single pad or bridging two neighbours will brick the board, and there is no schematic to debug it.
  • Apple does not document the mainboard, so you are reverse-engineering. If iOS refuses to boot after the swap, you have no official support and no repair manual.
  • The grey-market NAND supply chain is opaque. You may receive a chip that reports 1TB but fails after a month, and you will not know until the phone is already reassembled.
  • This voids warranty and may make the phone uninsurable. If something else breaks later, Apple will refuse service because the board has been modified.

Does this work on other iPhones, or just the Duo?

The technique applies to any iPhone with soldered NAND, but the chip pinout and iOS pairing changes with every model. The Duo is Apple's first foldable, so this is new territory — there is no public history of successful upgrades yet.

Will iOS accept the new chip without additional firmware patches?

DirectorFeng shows iOS booting and recognising 1TB in Settings. Whether that means full compatibility — no kernel panics, no data corruption under load — is not proven in a 33-minute video. Long-term stability is unknown.

Where do I buy the 1TB flash chip?

DirectorFeng does not say. Grey-market NAND comes from salvaged devices, overstock, or factories that quietly sell spare chips. You will need to identify the original chip on the 1TB model and find a supplier, which is its own research project.

Can I do this without a BGA rework station?

No. A hot air pencil aimed freehand will overheat neighbouring components or underheat the chip. BGA reflow needs even heat, controlled ramp rates, and a preheater under the board. Attempting this with a paint-stripper heat gun will destroy the board.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Apple's $600 storage markup has always rewarded people who can solder, but a foldable changes the stakes — one slipped tool and the hinge is toast. If you have done BGA work before, what would make you attempt this versus just buying the 1TB model outright?

CompareeTEAM9d ago

Practical notes from our verification: this is the only public documentation of an iPhone Duo storage upgrade, published 24 October 2026, one day after the phone went on sale. The single biggest unknown is not the soldering — it is whether grey-market NAND will stay stable under iOS, because Apple does not publish compatibility lists and a chip that boots is not the same as a chip that survives a year of writes.

DirectorFeng

DirectorFeng is a microsoldering technician and videographer who documents high-risk electronics modifications. This iPhone Duo upgrade was published the day after the phone went on sale, making it one of the first public teardowns of Apple's foldable.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.