TURN CAR IGNITION COILS INTO A SPEAKER THAT PLAYS MUSIC THROUGH SPARKS

Turn junkyard car ignition coils into a Bluetooth speaker that plays music through 60,000-volt sparks.

by Jay Bowles

AudioWorkshop

difficulty
●●●●○
time
no build time given in the video
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

This is a demonstration build, not a documented project. Jay Bowles of Plasma Channel builds a dual ignition coil driver that plays Bluetooth audio through high-voltage sparks. A single Honda coil turns 15 volts into about 15,000, and with two coils wired anti-parallel (one connected backwards) the output voltage doubles; the video description calls it a 60,000 volt power source. The driver is a 555 timer circuit that pulses 12 to 18 volts DC into the coils as a square wave at about 1 to 10 kilohertz, with potentiometers for tuning, an audio input, a snubber to protect the MOSFET and a Bluetooth receiver for wireless playback. The video description names some of the parts, but there is no downloadable schematic, no PCB layout and no code, so you would be working from what is shown on screen. The sound is rough with a background tone, nowhere near the Lansche plasma-tweeter loudspeakers that start around 25,000 to 30,000 dollars a pair. The real risk is the voltage: tens of thousands of volts can arc to anything nearby, and Jay's earlier, simpler version of the circuit exploded. If you already build high-voltage circuits, this is a fun experiment. If you have never worked with high voltage, this is not the project to learn on.

GOOD TO KNOW

  • —The build exists only as a YouTube video. Jay Bowles of Plasma Channel demonstrates the circuit, and the video description names some of the parts.
  • —There is no repository, no Gerber files, no schematic file, no firmware, and no BOM spreadsheet.
  • —Parts mentioned in the video and description: 555 timer, IRFP260N MOSFET, 10k potentiometers, 150 nF snubber capacitor, 47 nF timing capacitor for the 555, 1k resistors, 5 V regulator, Bluetooth receiver, snubber resistor and diode, two matching ignition coils. The description says this is only part of the circuit.
  • —The video is sponsored content (Truebill), so some runtime is not technical.
  • —No licence stated because there is no repository or design file release.

Parts to buy

11 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Two matching ignition coils (Jay found his at junkyards)Find
  • 555 timerFind
  • IRFP260N MOSFETFind
  • 10k potentiometersFind
  • 150 nF snubber capacitorFind
  • 47 nF timing capacitorFind
  • 1k resistorsFind
  • Snubber resistor and diodeFind
  • 5 V regulatorFind
  • Bluetooth receiver with an audio jackFind
  • 12-18 V DC power supplyFind

Can I build this?

Printnothing required
BuyTwo matching ignition coils (Jay found his at junkyards), 555 timer, IRFP260N MOSFET, 10k potentiometers, 150 nF snubber capacitor, 47 nF timing capacitor, 1k resistors, snubber resistor and diode, 5 V regulator, Bluetooth receiver with an audio jack, 12-18 V DC power supply. Jay also used an acrylic stand and banana plugs for input and output. The video description says its list covers only some parts of the circuit.
ToolsNot listed in the video. Expect basic electronics tools such as a soldering iron and a multimeter, plus a clear, insulated workspace.
SkillsIntermediate to advanced electronics. You need to understand MOSFETs, duty cycle, snubber circuits, and high-voltage safety. No PCB design or firmware required, but you are building from a video demonstration, not a schematic.
TimeThe video does not give a build time.
Cost$$. The video does not give a total cost. Jay's coils came from junkyards; the rest is common electronic parts plus a 12-18 V DC power supply.
SafetyGenuine high-voltage hazard. 60,000 volts will arc across air gaps and through skin. Sparks generate ozone, which is a respiratory irritant. Work in a ventilated space, keep flammable materials away, never touch the coil terminals or spark gap while powered, and discharge capacitors before handling. If you have a pacemaker or other implanted device, do not build this.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Plasma Channel: Bluetooth dual ignition coil driver

Jay Bowles explains the 555 driver and snubber, finds a matching second coil at a junkyard, wires the dual coils anti-parallel, plays Bluetooth music through the sparks and tries turning the spark gap into a radio transmitter. Contains a sponsored segment (Truebill).

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the full Plasma Channel video from start to finish before deciding anything. (There is no schematic file. The description names only some of the parts.)
  2. 2.Understand the driver: a 555 timer sends an adjustable square wave at about 1 to 10 kilohertz to a MOSFET, which switches 12 to 18 volts DC into the ignition coils.(Potentiometers tune the frequency and performance.)
  3. 3.Note the protection and the Bluetooth add-on: a resistor, diode and capacitor snubber protects the MOSFET, and a 5 V regulator powers a Bluetooth receiver whose audio goes into pin 5 of the 555.(Jay's earlier version without the snubber exploded.)
  4. 4.See how the dual coil works: both coils are powered at the same time, one connected backwards (anti-parallel), which doubles the output voltage.(Jay searched a whole wrecking yard to find a coil identical to the one he already had.)
  5. 5.Listen to the results: the music comes through with a constant background tone.(Higher frequencies give clearer audio but much smaller, quieter arcs, because ignition coil iron cores heat up from eddy currents.)
  6. 6.Connect the Bluetooth receiver to the 555 audio input. Pair your phone and play a track.(The first attempt sounded rough, with a constant background pitch at every frequency setting. Higher frequencies sound clearer but much quieter. This is not hi-fi.)

KNOWN ISSUES

  • Using two different coils. Jay drove to a wrecking yard and searched through about 100 cars to find the exact twin of the coil he already had for the dual setup.
  • Skipping the snubber circuit. 555 drivers that switch inductive loads tend to blow themselves up, and Jay's earlier version without the upgrades exploded. The resistor, diode and capacitor snubber is there to protect the MOSFET.
  • Underestimating the arc distance. Keep the workspace clear and insulated.
  • Building this as a first high-voltage project. The output is tens of thousands of volts and things go wrong fast. Get experience and supervision with high-voltage work before attempting anything like it.
  • Expecting hi-fi sound. The output is a raspy sound with a background tone that stays at every frequency setting. Higher frequencies sound clearer but get much quieter. Commercial Lansche plasma-tweeter loudspeakers start around 25,000 to 30,000 dollars a pair; this is not a substitute.
  • Ignoring ozone buildup. Sparks make ozone, which smells sharp and irritates your lungs. Run this in a well-ventilated space or outdoors, and do not run it for hours.

Can I use a different MOSFET?

The video uses an IRFP260N MOSFET and does not test any substitutes. The 555 driver switches an inductive ignition coil, and Jay adds a snubber because these drivers tend to blow themselves up, so any replacement should be chosen with that in mind.

Do I need an oscilloscope?

The video does not say one is required. Jay tunes the driver with potentiometers and sweeps the 1 to 10 kilohertz range by ear while listening to the sparks.

How loud is it?

Not very loud, and not clean. The sound is rough with a background tone that stays at every frequency setting. At the highest frequencies the music is clearer but much quieter, because the iron cores of ignition coils lose energy to eddy currents and the arcs get smaller. It is a high-voltage demonstration that plays music, not a speaker replacement.

What power supply does it need?

The 555 driver accepts 12 to 18 volts DC. A 5 V regulator powers the Bluetooth receiver from the same supply. The circuit pulls a fair amount of current when driving both coils.

What is the snubber doing?

Drivers like this, switching an inductive load, tend to blow themselves up. Jay adds a resistor, diode and capacitor as a snubber to protect the switching transistor from the spikes the coil produces when it is switched off. An earlier, simpler version of his circuit without these upgrades exploded.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Two junkyard ignition coils, a 555 timer and a Bluetooth receiver play music through high-voltage sparks, but the sound is rough and there is no schematic to follow. Would you rather watch this one, or save up for Lansche plasma-tweeter loudspeakers that start around 25,000 dollars a pair?

CompareeTEAM27d ago

Practical notes from our verification: the only source is the YouTube video. There is no repository, no schematic file and no PCB layout, and the description names only some of the parts. The video contains a sponsored segment (Truebill), so the technical content is shorter than the total length. The biggest surprise: the sound is much rougher and quieter than the visual drama suggests. This is a high-voltage demonstration that happens to play music, not a practical speaker.

Jay Bowles

Jay Bowles runs Plasma Channel, a YouTube channel about high-voltage and plasma experiments. He found the first ignition coil for this build at a junkyard about a decade ago, and this video is the follow-up to an earlier, simpler coil driver he built a couple of years before.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.