TURN YOUR DESK INTO THE AIRPOWER APPLE CANCELLED

A desk that charges your phone wherever you put it — using one moving coil instead of 600 fixed ones.

by HTX Studio

WorkshopAutomation

difficulty
●●●●●
time
About 2 months for the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

HTX Studio spent two months building a desk that charges a phone anywhere on its surface, the idea Apple cancelled as AirPower in 2019. Covering the top with coils would have needed around 600 of them, so instead a camera above the desk spots the phone and motors drive a single wireless charging coil underneath it. The top is a transparent screen. When one device is full, the coil moves to the next, and parked under the keyboard it charges the keyboard through a receiver coil. Two fixed coils in the corners take extra devices. A Mac mini sits inside the desk, after an hour of sitting the desk lights up and shows a raise button for the standing legs, and a 25-minute focus mode refuses to charge a phone picked up early. With several phones the single coil just shuttles between them rather than charging them all at once. The hardest truth: there is no repository, no published files, no BOM, no code and no build guide. You have a five-minute YouTube video and that is it. If you want to build this, you are working out every part yourself: the camera tracking, the motor control, the mechanism that moves the coil, the transparent screen, the wireless charging setup and the software that decides where to drive the coil. If you can design that from footage, it is an inspiring reference build. If you were hoping for STLs and a parts list, there are none.

GOOD TO KNOW

  • —No repository, no build guide, no published files.
  • —The project was built by HTX Studio and documented in a single YouTube video.
  • —No CAD, BOM, code, wiring diagrams, or assembly instructions are public.
  • —No licence is stated because nothing is released.
  • —This is a showcase build, not a project you can replicate without reverse-engineering the video.

Parts to buy

7 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • MotorsFind
  • Wireless charging coilFind
  • Receiver coil for the keyboardFind
  • Two fixed corner coilsFind
  • CameraFind
  • Transparent screenFind
  • Standing desk legs and a Mac miniFind

Can I build this?

Printnothing published
BuyMotors, a wireless charging coil, a receiver coil for the keyboard, two fixed corner coils, a camera, a transparent screen, standing desk legs and a Mac mini; no models are specified
ToolsNot shown in detail; no tool list is given
SkillsMechanical design, motor control, camera-based tracking, programming and wireless charging electronics
TimeHTX Studio spent two months, including a first prototype and a rebuild
CostNot stated by HTX Studio; the build includes a transparent screen, standing desk legs, motors and a Mac mini
SafetyLow-voltage electronics with no special risks beyond ordinary powered gear. Keep fingers clear of the moving coil mechanism while testing.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

AirPower Desk Build5:00

About 5-minute narrated build video: explains the idea, the prototype problems and the desk features, but gives no part numbers, measurements, wiring or code

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the YouTube video and decide if you can reverse-engineer a gantry system, camera tracking, and wireless power control from footage alone (This is the only public documentation)
  2. 2.Work out a mechanism that can move one charging coil under any spot on your desk(The video shows motors moving the coil but gives no dimensions or part models)
  3. 3.Set up a camera above the desk and write or adapt computer vision code to detect phone position(No code is published; you are writing this from scratch or adapting an existing CV library)
  4. 4.Wire the wireless charging coil to move with the gantry and implement a cable management system that does not tangle(The first prototype had cable problems, so HTX Studio built a double-ended cable reel; the creator also mentions that a linear slide with no moving wires would have been faster)

KNOWN ISSUES

  • There is no repository, no BOM, no code, and no build guide — you are reverse-engineering a five-minute video.
  • The coil-moving mechanism, motor control, camera tracking and wireless charging setup are all custom and undocumented.
  • The single moving coil means multiple devices charge one at a time, not simultaneously — if you expected true multi-device charging like the original AirPower concept, this does not do that.

Is there a build guide or files I can download?

No. There is no repository, no CAD, no code, no BOM, and no written instructions. You have a five-minute YouTube video and that is it.

Can it charge multiple phones at the same time like the original AirPower concept?

No. The single moving coil shuttles between devices one at a time. Two fixed coils in the corners help, but this is not simultaneous multi-device charging.

What motors and controller does it use?

Not specified. The video shows motors driving a single charging coil under the desk and says the second version got faster motors and a double-ended cable reel, but no motor models, controller or specs are given.

How does the camera track the phone?

Not documented. You see a camera above the desk in the footage, but the code, frame rate, detection algorithm, and calibration process are not shown or explained.

How long did it take HTX Studio to build?

Two months, including a first prototype whose motors were too slow and whose moving cables got in the way, followed by a rebuild.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

HTX Studio spent two months and built two versions to get the coil moving fast enough and the cables out of the way. If you were building this from the video alone, which system would you tackle first: the camera tracking, the motor control, or the wireless charging?

CompareeTEAM21d ago

Practical notes from our verification: this is a showcase build with no public repository, no released files and no build guide. The only documentation is a roughly 5-minute YouTube video that explains the idea and shows the build, but does not include measurements, part numbers, wiring or code. HTX Studio is on YouTube and on Instagram at @htx_studio. The transparent desk surface and the coil-moving mechanism are both custom, and working out either one from footage is a significant project on its own. If you are looking for a replicable wireless charging build, this is not it, but if you want to see a polished concept build and can design the mechanics and software yourself, it is a strong reference.

HTX Studio

HTX Studio had waited for Apple's AirPower since it was shown in 2017, only to see it cancelled in 2019. So they spent two months building the idea into a whole desk. The first prototype had motors that were too slow and moving cables that got in the way, so the second version got faster motors and a double-ended cable reel.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.