MAKE A SUPERCONDUCTOR AT HOME THAT MAKES A MAGNET FLOAT
NileRed made a real high-temperature superconductor that floats a magnet. It took lab chemicals, a roughly US2000 dollars tube furnace, pure oxygen and liquid nitrogen, and several failed runs along the way.
by NileRed
- difficulty
- ●●●●●
- time
- no total build time given in the video; a standard furnace cycle was about an hour of heating, a 10-hour hold at 920 °C and about 18 hours of slow cooling, the final run held 920 °C for 24 hours, drying the yttrium nitrate took several days, and the creator says projects like this take months
- license
- license not specified
- repo
- repo
●●●●● · no total build time given in the video; a standard furnace cycle was about an hour of heating, a 10-hour hold at 920 °C and about 18 hours of slow cooling, the final run held 920 °C for 24 hours, drying the yttrium nitrate took several days, and the creator says projects like this take months · license not specified · repo
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
NileRed made YBCO (yttrium barium copper oxide), one of the few practical high-temperature superconductors. The payoff is real: cooled in liquid nitrogen, his pellets float a neodymium magnet thanks to the Meissner effect and flux pinning. Many superconductors need extreme cold (mercury only works below −269 °C), but YBCO superconducts below −181 °C, so liquid nitrogen is enough. He purified eBay yttrium oxide into yttrium nitrate, combined it with copper nitrate and barium nitrate (barium nitrate is toxic), turned the mix into a metal-oxide powder, then fired it in a tube furnace he bought from Alibaba for about US2000 dollars under a flow of pure oxygen: about an hour up to 920 °C, a 10-hour hold, and slow cooling at 50 °C per hour. Only the form with seven oxygens superconducts, so the powder was pressed into pellets with a die set and a hydraulic press and fired again with oxygen. His first pellet worked; a later batch of five failed completely, which he traced to too little oxygenation, so he ground them up and re-fired them. A final 24-hour hold instead of 10 hours made the magnet float significantly higher and let a pellet hold a much larger magnet. This is lab chemistry, not a home project from household items: it involves toxic and corrosive chemicals, a 920 °C furnace, a pressurised oxygen supply and liquid nitrogen. For most people this is a watch-only project.
IN THE REPO
GOOD TO KNOW
- —This is a YouTube demonstration, not a repository build.
- —No CAD files, BOM or creator-written guide exists. The video description links the written procedures he followed.
- —The video shows what he did: preparing a metal-oxide powder from the nitrates, firing it in a tube furnace under oxygen at 920 °C, pressing pellets and firing them again with oxygen.
- —A 24-hour bake instead of 10 hours produced significantly better results: the magnet floated higher and the pellet held a much larger magnet.
- —He used yttrium oxide (converted to yttrium nitrate), copper nitrate, barium nitrate (toxic), citric acid, ammonia and nitric acid, plus a tube furnace, an oxygen tank, a die set, a hydraulic press and liquid nitrogen.
- —No licence is stated; this is a chemistry demonstration, not software or hardware.
Parts to buy
8 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
Can I build this?
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
Making a superconductor45:38
Full video (about 45 minutes) from preparing the chemicals to floating a magnet: the furnace mishap, the first working pellet, the failed batch, the 24-hour bake comparison, and the Meissner effect in liquid nitrogen.
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Watch the NileRed video in full (About 45 minutes. Watch it as a demonstration of what NileRed did, not as a recipe.)
- 2.Understand what it actually took(Lab chemicals including toxic barium nitrate and concentrated nitric acid, a tube furnace that reaches 920 °C (about US$2000 from Alibaba in his case), a pure oxygen supply, a die set and hydraulic press, and liquid nitrogen.)
- 3.Know the hazards(Toxic and corrosive chemicals, a 920 °C furnace, pressurised oxygen and liquid nitrogen. NileRed did this in a lab; this is not a project from household items.)
KNOWN ISSUES
- This needs a tube furnace that holds 920 °C for many hours with a pure oxygen flow. NileRed's cost about US$2000, and that is the first and largest barrier.
- Barium nitrate is toxic, and the process also uses concentrated nitric acid and ammonia. Without lab safety training and proper lab equipment, this is not safe to attempt.
- Oxygenation is critical. A batch of five pellets failed completely, and NileRed said that if re-oxygenating had not fixed it, he would have had no idea what went wrong.
- The effect only lasts while the pellet is colder than its critical temperature. As soon as it warms up in the air, the levitation stops.
- Expect several rounds. NileRed re-ran the powder, re-fired pellets that failed, and did a final 24-hour hold that gave much better results than the 10-hour one.
- There is no repository, BOM or creator-written guide. The video description links the written procedures he used, and he says one widely shared procedure had calculation errors.
Can I use a different furnace or oven?
The video does not test other furnaces. Most procedures he found called for a tube furnace with pure oxygen; he mentions that Ben from Applied Science instead modified a tabletop furnace and rigged it to an oxygen tank. NileRed bought a tube furnace.
How much does a tube furnace cost?
NileRed says his Alibaba tube furnace cost about US$2000 in total, compared with about US$5000 or more for the ones he found elsewhere. It arrived in a broken crate, and he then damaged it himself by plugging it into the wrong voltage; it needed a new transformer.
Is YBCO the only high-temperature superconductor?
No. He says other superconductors also work with liquid nitrogen, but he could not find much information on making them and they seemed more difficult, so YBCO looked like the best option.
Can I scale this up to make a levitating train or power cable?
The video does not cover anything like that. It shows small pellets floating a magnet, and a pellet riding a magnet track, while cold in a dish of liquid nitrogen. It is a demonstration, not an engineering prototype.
What happens if I get the oxygen bake wrong?
In the video, a batch of five pellets looked fine but did not float the magnet at all. NileRed concluded they were not oxygenated enough, ground them back into powder and fired them again with oxygen, after which they worked.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
NileRed's batch of five pellets failed completely until he ground them up and re-oxygenated them. Did you expect a superconductor to depend that much on a few missing oxygen atoms?
NileRed
NileRed is a chemistry YouTuber. He wanted to try this after seeing a short video of a magnet floating over a superconductor about two years earlier, while researching his ferrofluid project. He says big projects like this take months to put together.
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM27d ago
Practical notes from our verification: there is no GitHub repo, no BOM and no creator-written guide; the video description links the written procedures he followed, and he says one widely shared procedure had calculation errors. He bought yttrium oxide and copper nitrate on eBay and barium nitrate from a chemical company, and the tube furnace from Alibaba for about US$2000. The Instagram handle is @nile.red. The biggest barrier is not one step of the chemistry but everything together: a 920 °C tube furnace with pure oxygen, toxic chemicals and liquid nitrogen. Even with all that, his batch of five pellets failed until he re-oxygenated them. For most people this stays a watch-only project.