TURN AN OLD RIDING MOWER INTO A BACKHOE

A 1980 John Deere 210 riding mower turned into a working backhoe from P.F. Engineering plans, for about 1,300 to 1,400 dollars in backhoe parts alone.

by Think DIY

Workshop

difficulty
●●●●○
time
75 hours over two and a half months
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Think DIY took a 1980 John Deere 210 riding mower and added a working backhoe, following plans from P.F. Engineering. The build took about 75 hours over two and a half months, and the backhoe alone cost roughly 1,300 to 1,400 dollars — that figure does not include the hydraulic pump or the loader they had already built for the same tractor. The steel yard only had thicker stock than the plans specified, so the finished backhoe weighs about 375 to 400 pounds instead of the roughly 350 pounds in the plans. Fourteen hydraulic hoses connect to a lever valve of about 250 dollars, and they labeled the levers with stickers; they skipped joystick controls because those cost about three times as much. The seat flips up and rotates so one seat serves both driving and digging. The most likely problem is underestimating the weight and finding that your mower cannot safely carry the finished assembly. Hydraulics under pressure are a real hazard: a leaking fitting or burst hose can spray oil, and the moving arm can pinch or crush. For comparison, a new John Deere 1025R compact tractor with a loader and backhoe lists at 43,999 dollars. This one is a small machine for light digging, not a replacement for a real excavator.

GOOD TO KNOW

  • —This is a build from P.F. Engineering plans, not an open-source repository.
  • —The video shows the finished backhoe and its first digging; it does not include the plans themselves.
  • —No CAD files, BOM or downloadable files are known for this build.
  • —The cost shown does not include the hydraulic pump and loader already on the tractor.

Parts to buy

8 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • P.FFind
  • Engineering plansFind
  • Steel stockFind
  • Hydraulic parts including 14 hoses and a lever valveabout 250 USDFind
  • PaintFind
  • Hydraulic pump is required but not included in the 1Find
  • 300 to 1Find
  • 400 dollar figureFind

Can I build this?

Printnothing required
BuyThe P.F. Engineering plans, steel stock, the hydraulic parts including 14 hoses and a lever valve (about 250 USD), plus paint. A hydraulic pump is required but not included in the 1,300 to 1,400 dollar figure.
ToolsA welder and an angle grinder, tools for cutting and drilling steel, wrenches for the hydraulic fittings, painting supplies, and a vinyl cutter if you want decals like theirs.
SkillsWelding and metalworking, reading plans, cutting and fitting steel, and basic hydraulics. The builders described themselves as rookies and labeled every lever to avoid mistakes, so patience matters as much as experience.
Timeabout 75 hours of work over two and a half months, assuming you already have the tools and a workspace set up
Cost$$: about 1,300 to 1,400 USD for the backhoe alone, including a lever valve of about 250 USD. Not included: the hydraulic pump and the loader from the earlier build. For comparison, a new John Deere 1025R with loader and backhoe lists at 43,999 USD.
SafetyWelding hazards (sparks, UV, fumes, hot metal), angle grinder kickback, and heavy steel that can crush fingers or fall. Hydraulic fluid is under pressure: a loose fitting or burst hose can spray oil, so never check for leaks with your hand. The moving boom of a roughly 400 pound backhoe can pinch or crush, so test every movement slowly, stay clear of the arm, and never put yourself under the raised boom. Use it for light digging only.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

It's Done! (part 7)

Unveiling of the finished backhoe: the flip-up rotating seat, the lever valve with labeled controls, cost and weight, then the first digging. This is part 7 of the build series.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Get the plans(The builders worked from P.F. Engineering plans. The plans are not included in the video and are not available on this page.)
  2. 2.Check your mower's capacity(The John Deere 210 weighs about 600 pounds. The finished backhoe weighs 375 to 400 pounds. Make sure your mower frame and rear axle can handle the load, especially if you use thicker steel.)
  3. 3.Price the hydraulics(The lever valve alone was about 250 dollars; joystick controls cost roughly three times that. The backhoe has 14 hydraulic hoses, and you need a hydraulic pump if you do not already have one.)
  4. 4.Watch the video series (Part 7 shows the finished backhoe, the controls, the cost and weight, and the first digging.)

KNOWN ISSUES

  • The 1,400 dollar cost does not include the hydraulic pump or the loader — those were already on the tractor from an earlier build. Budget for a pump if you are starting from scratch.
  • Thicker steel than the plans call for makes the backhoe heavier. The builder used what the steel yard had in stock and the assembly came out 375 to 400 pounds instead of the planned weight. Check your mower's rear axle capacity before you commit.
  • Fourteen hydraulic hoses are easy to mix up. The builder made stickers to label which lever operates which function. Plan for that before the first test.
  • Joystick controls cost about three times as much as a lever valve. The builder chose levers to save money; if you want joysticks, budget accordingly.
  • This is not a replacement for a real excavator. It is a small machine for light digging, and the hydraulics are under pressure: a leaking fitting or burst hose can spray oil, and the arm can pinch or crush. Stay clear of the moving boom and never put yourself under it.
  • Welding, grinding and fitting heavy steel takes time. The 75 hours is the builders' own count over two and a half months, and they said it felt like six.

Can I build this without the plans?

The builders worked from P.F. Engineering plans. This video is the unveiling of the finished machine, so it does not give you the plan dimensions or a cutting list. Without the plans you would be reverse-engineering the whole design from footage.

Will this work on other riding mowers?

The builders used a 1980 John Deere 210 that weighs about 600 pounds without the mower deck, and their finished backhoe came out at roughly 375 to 400 pounds. The source does not say which other mowers the plans fit, so check that your own mower's frame and rear axle can carry that load before you start.

How much digging can it actually do?

It is a small machine for light digging. The builders were happy with how it dug, but it is not a replacement for a real excavator.

Do I need the loader too?

The backhoe uses the hydraulic pump the builders had already bought for their earlier loader build on the same tractor. If you do not have that pump, you need one, and it is not included in the 1,300 to 1,400 dollar figure.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

Fourteen hydraulic hoses, a 250 dollar lever valve, and about 1,300 to 1,400 dollars for the backhoe alone turned a 1980 riding mower into a small digging machine. What would you dig first?

CompareeTEAM25d ago

Practical notes from our verification: this is built from P.F. Engineering plans, not open source, and the video is the unveiling of the finished machine, so you will not get dimensions or a cutting list from it. The 1,300 to 1,400 dollar figure is the backhoe only and assumes you already have a hydraulic pump — the builders had one from an earlier loader project on the same tractor. The finished backhoe came out heavier than planned because the steel yard only had thicker stock, so check your mower's rear axle capacity before you weld anything. Treat the hydraulics with respect: pressurized oil can leak or spray, and the arm can pinch or crush.

Think DIY

Think DIY (@just_think_diy) is a YouTube channel that documents its builds. The riding mower backhoe followed their earlier loader build on the same 1980 John Deere 210, and the backhoe was built from P.F. Engineering plans.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.