TURN A 256GB IPAD PRO INTO A 2TB ONE

A repair channel in China grinds the original memory off a 256GB iPad Pro M5 and fits two new chips, and it boots with 2TB of storage.

by DirectorFeng

Open-hardware

difficulty
●●●●●
time
not stated in the video
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

DirectorFeng's video shows a 13-inch iPad Pro M5 going from 256GB to 2TB of storage, but the procedure is professional microsoldering. The original memory sits so close to the M5 processor that it was ground off instead of heated off. The board then needed the missing power lines for its spare memory position completed before two Toshiba K8A9 chips went on with fresh solder balls, BGA underfill and a reflow at a constant 100°C. After reassembly with new thermal paste, the iPad boots with 2TB. Only the storage changes: Apple's own 2TB model also has 16GB of RAM and a 10-core CPU. Apple sells the 256GB model for 1,499 dollars and the 2TB model for 2,599 dollars; the video does not give a price for the upgrade. It voids the warranty, there is no written guide, and it is not a home project.

GOOD TO KNOW

  • —This is professional microsoldering work documented in a single 31-minute repair video without narration, not a step-by-step build guide.
  • —No schematic, BOM, or source files — the video shows the procedure but assumes you already know board-level repair.
  • —The video shows grinding off the old memory, completing the missing power lines, reballing with fresh solder balls, BGA underfill, a reflow at a constant 100°C and new thermal paste.
  • —This voids the warranty and is professional microsoldering, not a home project.
  • —No licence applies — this is a repair technique, not open-source hardware.

Parts to buy

4 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Two Toshiba K8A9 NAND chipsFind
  • Solder ballsFind
  • BGA underfill and thermal pasteFind
  • 13-inch iPad Pro M5 you are willing to riskFind

Can I build this?

Printnothing required
Buytwo Toshiba K8A9 NAND chips, solder balls, BGA underfill and thermal paste, plus a 13-inch iPad Pro M5 you are willing to risk
Toolsa BGA reflow station, magnification, tweezers, a way to grind off the old chips, reballing gear, underfill and thermal paste
SkillsProfessional microsoldering and board-level repair — if you have not reballed BGA chips before, this is not the project to learn on
Timenot stated; the video runs 31 minutes and is edited
Cost$$$: the video gives no price for the chips or the upgrade, and you need professional rework equipment
SafetyThe iPad has a large lithium-ion battery, so take care not to damage it while opening the device. Grinding off the old memory is destructive, erases the data and voids the warranty. This is professional repair work.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

iPad Pro M5 256GB to 2TB storage upgrade31:08

Shows disassembly, grinding off the old NAND, adding power lines, reballing and placing two 1TB chips, underfill, reflow at 100°C, reassembly, and successful boot with 2TB.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the entire video first (The procedure is shown in real time but not explained step-by-step — you need to already know microsoldering to follow it.)
  2. 2.Source two Toshiba K8A9 1TB NAND chips(The part number is in the video description. No supplier is given.)
  3. 3.Open the iPad and remove the logic board(Shown around 2:20 in the video.)
  4. 4.Grind off the original memory chips(They sit too close to the M5 to heat off safely. This step is destructive and cannot be undone.)
  5. 5.Add missing power lines for the second memory position(The board has a spare memory position, and its missing power lines have to be completed before 2TB works (around 15:40).)
  6. 6.Reball the new chips, place them, apply underfill, and reflow at 100°C(Two Toshiba K8A9 chips go on with fresh solder balls, then BGA underfill and a reflow at a constant 100°C.)
  7. 7.Reassemble with new thermal paste and test(After reassembly with new thermal paste, the iPad boots with 2TB of storage (around 29:40 to 30:40).)

KNOWN ISSUES

  • Only the storage changes. Apple's own 2TB iPad Pro also has 16GB of RAM and a 10-core CPU, so this is not the same as buying the 2TB model.
  • Grinding off the original memory is destructive and cannot be undone, and the chips sit very close to the M5 processor.

Does this give me the same iPad as the $2,599 model?

No. Only the storage changes. Apple's own 2TB model also has 16GB of RAM and a 10-core CPU, while the 256GB model has 12GB and 9 cores.

Can I pay someone to do this for me?

The video does not name a service or a price. This iPad belonged to a viewer who sent it to DirectorFeng for the upgrade.

What happens to my data?

It is gone. The original NAND chips are ground off, so you lose everything that was on them. Back up before disassembly.

Will Apple service the iPad after this?

The mod voids the warranty.

Where do I buy the Toshiba K8A9 chips?

The video gives the part number, Toshiba K8A9, but no supplier, and we do not link one.

Can I do this on the 11-inch iPad Pro?

The video only shows the 13-inch iPad Pro M5, so we cannot say whether the 11-inch model works the same way.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

DirectorFeng ground the original chips off instead of heating them because they sit too close to the M5 processor. If you were doing this repair, would you risk the heat or commit to grinding?

CompareeTEAM18d ago

The new chips are two Toshiba K8A9, the reflow is held at a constant 100°C, and the missing power lines for the spare memory position are completed around 15:40. The video has no narration, only burned-in subtitles and a description. There is no schematic, no written guide, no price for the upgrade, and no source for the chips beyond the part number.

DirectorFeng

DirectorFeng is a repair channel from China. A viewer sent in this 13-inch iPad Pro M5 to have its storage upgraded from 256GB to 2TB.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.