MAKE DRY ICE AT HOME FROM BAKING SODA AND POOL ACID
Hyperspace Pirate turned baking soda and hydrochloric acid into CO2 gas, compressed it with a fridge compressor, and flash-froze it into dry ice at minus 79 C.
by Hyperspace Pirate
- difficulty
- ●●●●●
- time
- a full day plus setup
- license
- license not specified
- repo
- repo
●●●●● · a full day plus setup · license not specified · repo
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
This is a chemistry demonstration that proves you can synthesise dry ice at home, and it is fascinating to watch. Pool hydrochloric acid (31 percent) reacts with baking soda to produce CO2, which passes through a desiccant and fills a 24 inch beach ball with roughly 215 grams of the gas. A salvaged fridge compressor then pumps it into a paintball tank. At room temperature CO2 needs about 1,000 PSI to condense, but the small mini fridge compressor barely reaches 500, so the tank sits in an ice bath to liquefy the gas at lower pressure. When released through a nozzle, the liquid flash-freezes into dry ice at minus 79 C. The tank collected about 488 grams. The creator is honest: it is not practical. His bigger compressor burned out, and a fitting popping at 1,000 PSI could easily be lethal. The video is a proof of concept, not a weekend project. If you want to understand the phase diagram of CO2 and see the chemistry work, it delivers. The single thing most likely to go wrong is underestimating the pressure hazard or the acid fumes.
IN THE REPO
GOOD TO KNOW
- —This is a YouTube demonstration, not a build guide with files or a bill of materials.
- —The video shows the chemistry and the pressure steps but does not list part numbers, fittings, or where to source a paintball tank rated for liquid CO2.
- —No repository, no CAD, no step-by-step written instructions.
- —The creator states plainly that it is not practical for regular use given the cost and time.
- —Safety gear and proper ventilation are essential; the video shows 31 percent hydrochloric acid and pressures up to 1,000 PSI.
- —There is no licence because there is no published design.
Parts to buy
12 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
Can I build this?
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
Hyperspace Pirate dry ice demonstration
The demonstration runs from the acid reaction through to the dry ice release. Timestamps in the story summary: acid and baking soda 0:00-2:43, beach ball collection 4:18, fridge compressor 6:31, pressure discussion 7:20, ice bath workaround 8:00, safety warning about fittings 9:10-9:49, final yield discussion 15:33.
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Watch the YouTube video to see the full process and the safety precautions in action (The video is the only documentation; there is no written guide.)
- 2.Source a paintball tank rated for liquid CO2 and verify it is pressure-tested(The tank must handle at least 1,000 PSI and be designed for CO2 phase change.)
- 3.Set up a ventilated workspace outdoors or in a fume hood before handling the acid(Acid fumes and CO2 displacement are both respiratory hazards.)
KNOWN ISSUES
- The video does not list part numbers for the fittings or the compressor, so you will spend time matching hose sizes and thread types; one wrong fitting at 1,000 PSI is catastrophic.
- The creator's bigger compressor burned out during the build, and the mini fridge one barely reaches 500 PSI; expect to spend extra on a compressor with headroom or accept the ice bath workaround.
- 31 percent hydrochloric acid is not the dilute stuff sold for cleaning; sourcing it in small quantities can be expensive or restricted in some regions.
- The ice bath is the only reason the low-pressure compressor works; without it you cannot liquefy the CO2, and the gas will vent when you open the tank.
- A fitting popping at 1,000 PSI can kill you; the creator says this plainly at 9:10-9:49, and it is the single most likely thing to go wrong.
- The yield is about 488 grams of dry ice, which sublimates in hours; for anything beyond a demonstration, buying dry ice or a pelletizer makes more sense.
Can I use a different acid or a lower concentration?
The video uses 31 percent hydrochloric acid because it reacts quickly with baking soda. Dilute acid will work but will take longer and produce more liquid waste. Sulfuric acid is not shown and reacts differently.
Why not skip the beach ball and pump directly from the reaction vessel?
The beach ball acts as a buffer so the compressor can pull a steady flow of dry CO2 without drawing in water vapour or acid mist from the reaction.
How long does the dry ice last?
Dry ice sublimates at minus 79 C; in open air it disappears in a few hours. In an insulated cooler it lasts longer but never more than a day or two.
Can I scale this up to make kilograms of dry ice?
The creator says it is not practical even at this scale.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
The creator collected about 215 grams of CO2 gas in a 24 inch beach ball, then compressed it into 488 grams of liquid. If you were doing this, would you build a larger gas collector first or invest in a stronger compressor?
Hyperspace Pirate
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM27d ago
Practical notes from our verification: this is a demonstration video with no published BOM, STL files, or step-by-step guide — the only documentation is the YouTube footage itself. The creator states at 15:33 that it is not practical for regular use, and his bigger compressor burned out during the build. The ice bath workaround is the only reason the mini fridge compressor works at all. The single biggest safety note is at 9:10: a fitting popping at 1,000 PSI could easily be lethal, and there is no list of which fittings he used or where to source a CO2-rated paintball tank. If you want to understand the chemistry and see it work, the video delivers; if you need dry ice for a project, a supplier sells it for a few euros per kilogram.