BUILD A DISH THAT DOWNLOADS PHOTOS OF EARTH
A second-hand 8 foot dish and a Raspberry Pi can pull full disk images of Earth from 22,000 miles up.
by Cranktown City
Built withRaspberry Pi
- difficulty
- ●●●●●
- time
- long project
- license
- license not specified
- repo
- repo
●●●●● · long project · license not specified · repo
WHAT YOU’LL NEED
Jump to section
COMPAREE VERDICT
This is a genuinely impressive build: a backyard dish that points itself at weather satellites and decodes full disk images of Earth from GOES-19, 22,000 miles away. But it is a build log, not a how-to. Cranktown City shows what he built (a new welded motorized mount with a ring gear, the reused mounting ring and linear actuator, a helix feed on a 3D printed scaffold, a Raspberry Pi with BTS7960 motor drivers, and a Sawbird LNA into an RTL-SDR running SatDump) and shows it working. You will be working out the metalwork, the motor control and the tracking code yourself. He openly says he knew basically nothing about the radio side when he started, and the video is honest about the dumb mistakes: a connector with no pin, interference from powering the LNA twice, and a feed sitting too close to the ground plane. Once the signal locked he got 8.5 to 9 dB with an error rate under 1%, then added tracking with CelesTrak orbit data, the Skyfield Python library and a PID loop to follow Metop passes, which needed a bladeRF instead of the RTL-SDR. He does not share what it cost. One more thing: GOES-16 was replaced by GOES-19 in 2025, and his first attempt failed because of it. Check which satellite is actually broadcasting before you aim.
IN THE REPO
GOOD TO KNOW
- —This is a video build log, not a repository. There are no CAD files, no BOM, no firmware in a repo, and no step-by-step guide.
- —The helix antenna is wound on a 3D printed scaffold designed by AZ Dave. The creator says it is linked in the video description; it is not part of this page.
- —The software is SatDump (free, open-source), the Skyfield Python library, and orbit data from CelesTrak. These are public tools, not part of this build.
- —The motorized mount is custom welded; the mounting ring and linear actuator were reused from the dish's original mount. You will need metalwork skills and equipment, or a way to get that done.
- —The video shows the final working system and explains the approach, but you will be reverse-engineering most of the mechanical and control details from timestamps and on-screen shots.
- —No licence is stated because there is no repository.
Parts to buy
10 itemsFrom our check of the build. Exact quantities and part numbers are in the creator’s BOM.
Can I build this?
Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.
Videos
I Built a MASSIVE Satellite Ground Station in My Backyard
The full build log. Key timestamps: 0:18 the dish, 1:42 reusing the mounting ring and linear actuator, 32:23 helix antenna on 3D printed scaffold, 33:53 LNA and RTL-SDR chain, 37:13 GOES-16 replaced by GOES-19, 39:44 raster scan, 40:27 full images from GOES-19, 42:47 orbit tracking with Skyfield, 43:41 Metop passes with bladeRF.
More builds like this
All projectsGallery
Start here
Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.
- 1.Check which GOES satellite is currently broadcasting(GOES-16 was replaced by GOES-19 in 2025 and stopped transmitting; his first attempt failed because of it.)
- 2.Watch the full video and note the timestamps for the mount, the control board, the feed and the signal chain (You are reverse-engineering this from the video. Pause and sketch.)
- 3.Source a large second-hand dish (his is 8 foot)(He found his on Facebook Marketplace and reused the mounting ring and linear actuator from its original mount.)
- 4.Design or adapt the motorized mount (ring gear for azimuth, linear actuator for elevation)(He welded the new mount himself; the original linear actuator was already strong enough to move the dish.)
- 5.Build the left-hand helix feed for GOES (about 1.694 GHz, right-hand polarized signal that the dish reverses)(He wound copper wire through a 3D printed scaffold by AZ Dave (linked in the video description), with a metal ground plate and an SMA connector soldered in the middle.)
- 6.Set up the Raspberry Pi with SatDump, the RTL-SDR and the LNA(That is his receive chain for GOES-19. Metop passes needed a bladeRF because of their higher bandwidth.)
KNOWN ISSUES
- Buying a dish and assuming the rest is straightforward. He welded a new motorized mount and built the helix feed, then still had to fix a pinless connector, power interference and the feed's position at the focal point before any data came through.
- Not checking which satellite is actually broadcasting. GOES-16 was replaced by GOES-19 in 2025 and no longer transmits data, so his first attempt picked up only background noise.
- Underestimating the signal chain. The video uses a Sawbird LNA right at the antenna, then an RTL-SDR. A female connector with no center pin and interference from powering the LNA through both USB and Bias-T each cost him signal before it worked.
- Expecting a tutorial. This is a build log, not a step-by-step guide. You will be working out the mount, the motor drivers, the tracking code and the RF chain from the video.
- Getting the feed position wrong. His first focal point sat too close to the ground plane; he made a small coupler to move the helix out so the focal point is centered on it.
- Ignoring the weather. He parks the dish in a stow position for storms, sealed the joints with silicone and notes it is begging to get struck by lightning. Even so, his elevation encoder lets water in when it rains.
Is this illegal?
No. GOES-19 and the Metop satellites send out public weather broadcasts, and this station only receives them. Nothing is hacked and nothing is transmitted.
Can I use a smaller dish?
The video does not test that. He used an 8 foot dish for GOES at about 1.694 GHz, 22,000 miles away, and still needed careful aiming and a raster scan to reach 8.5 to 9 dB. A smaller dish is untested here.
What is the total cost?
He does not say what the build cost, so there is no number to give. The dish itself came second-hand from Facebook Marketplace.
Can I skip the motorized mount and just point the dish at GOES manually?
GOES is geostationary, so for GOES alone the dish only has to point at one fixed spot. He used the motors and a raster scan to find it. The tracking is what lets the dish follow passing Metop satellites. A fixed, manually aimed dish is not tried in the video.
What is SatDump?
Free, open-source software with decoding pipelines for a large number of satellites. In this build it runs on the Raspberry Pi and decodes the GOES-19 images and the Metop passes.
Community builds
No community builds yet — be the first, we feature the best ones.
Discussion1
FROM THE COMPAREE TEAM
GOES-19 replaced GOES-16 mid-build and the first attempt failed because of it — satellites move and get decommissioned. If you were starting this today, would you go straight for auto-tracking or lock the dish on one bird and call it done?
Cranktown City
A YouTube maker who welds and builds motorized machines, and who admits he knew basically nothing about satellite reception before this project. He got hooked watching saveitforparts, bought an 8 foot dish on Facebook Marketplace and learned the radio side as he went. Next he wants swappable antennas and, eventually, radio astronomy.
DISCLAIMER
- Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
- Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
- Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.
CompareeTEAM15d ago
Practical notes from our verification: this is a video build log, not a repository, so there are no files to download and no step-by-step guide. You are working out the mount, the control system and the RF chain from the video. The software (SatDump, Skyfield, CelesTrak orbit data) is all public, and the RTL-SDR is a cheap USB radio. The helix scaffold is by AZ Dave, and the creator says it is linked in his video description. He does not share what the build cost. The single biggest surprise: GOES-16 was replaced by GOES-19 in 2025, and his first try failed because of it. Before you aim anything, check which satellite is actually broadcasting.