TURN A CAR ALTERNATOR INTO A GO-KART MOTOR

A 20-dollar Ford F-150 alternator, rewired in delta, drove a go-kart to 37 km/h for 10 minutes before one of its lead-acid batteries started to smell burning.

by Austin Blake

Workshop

difficulty
●●●●○
time
Build time not stated by the creator
license
license not specified
repo
repo
1
Jump to section

COMPAREE VERDICT

Austin Blake turned a 20-dollar Ford F-150 alternator into a go-kart motor. He removed the diode pack, found the ends of the six stator wire pairs with a multimeter continuity check and wired them in delta. The brushes stay, with 12 V on the rotor winding, while the stator runs at 48 V from the kart's lead-acid pack through a 48 V, 1500 W brushless controller that works with sensorless motors. The kart reached 37 km/h and drove for exactly 10 minutes before one of the lead-acid batteries started to smell burning; he concluded he had most likely over-discharged the pack, even with a 40 A fuse installed. Power was not measured. This is a short narrated video, not a full tutorial: there is no BOM, wiring diagram or written instructions, and the 20-dollar covers only the alternator. The controller, throttle, batteries and kart were extra. It is a good proof of concept for someone already comfortable with 48 V battery packs and brushless controllers, as long as the battery pack can handle the current.

GOOD TO KNOW

  • —This is a YouTube video build log, not a repository.
  • —No written instructions, BOM, or wiring diagram.
  • —The video shows the delta rewiring process with multimeter testing.
  • —No licence is stated for the video.
  • —The $20 is the alternator only; controller, batteries, throttle, kart, and wheels are extra.
  • —The ten-minute runtime ended with a battery over-discharge and burning smell.

Parts to buy

9 items

From our check of the build. Exact quantities and part numbers are in the creator’s BOM.

  • Used car alternatorthe video uses one from a 4.6 L Ford F-150, $20Find
  • 48 VFind
  • 1500 W brushless controller that works with sensorless motorsFind
  • 48 V battery pack that can handle the controller's currentFind
  • 12 V for the rotor windingFind
  • Foot throttleFind
  • 40 A fuseFind
  • Wire and heat shrinkFind
  • Existing go-kartFind

Can I build this?

Printnothing required
BuyUsed car alternator (the video uses one from a 4.6 L Ford F-150, $20), 48 V, 1500 W brushless controller that works with sensorless motors, 48 V battery pack that can handle the controller's current, 12 V for the rotor winding, foot throttle, 40 A fuse, wire and heat shrink, plus an existing go-kart
ToolsMultimeter with continuity check, soldering iron, heat shrink, wire strippers, basic hand tools for disassembly and mounting
SkillsIntermediate electrical skills: identifying stator wire pairs with a multimeter, soldering a delta connection, wiring a brushless controller and sizing a 48 V battery pack and fuse. Mechanical skills for mounting the motor on the kart.
Timea weekend is our estimate; the video does not say how long the build took. The conversion itself is disassembly, cutting the stator loose from the diode pack, continuity testing, delta wiring and reassembly; mounting and wiring on the kart depend on your setup.
Cost$$: the alternator cost $20. The controller, throttle, batteries and kart were extra and the video does not give their prices. For comparison, a ready-made Motenergy ME0709 kart motor is about $645.
SafetyA short on a 48 V battery pack can push very high current, melt wiring and start a fire. The controller can output up to 45 A; the creator ran a 40 A fuse, and a fuse is mandatory. His lead-acid batteries overheated and smelled burning after 10 minutes, so use a pack rated for the current and stop immediately at any hot or burning smell. Disconnect the battery before working on the wiring. The kart reached 37 km/h, so make sure the brakes work and wear protective gear before riding.

Build at your own risk. Projects involve tools, electronics and sometimes mains voltage — follow the creator’s safety notes.

Videos

Austin Blake alternator go-kart build

Narrated build: alternator overview (00:39), diode pack removal and multimeter identification of the six stator wire pairs (01:01-02:25), reassembly and controller setup (02:48-03:32), test ride result (06:53) and the battery overheating (07:13-07:35). No on-screen BOM or wiring diagram.

More builds like this

All projects

Gallery

Start here

Navigation into the creator’s own docs — we don’t rewrite the guide, we route you to the source.

  1. 1.Watch the YouTube video from 01:01 to 02:25 to see the diode pack removal and delta wiring process (Pause frequently to map the wire pairs; the multimeter continuity test is the key step)
  2. 2.Get a 48 V brushless controller that works with sensorless motors (the video uses a 48 V, 1500 W unit)(The controller model is not named in the video. His controller can output up to 45 A, so the battery pack and fuse must be chosen for that current.)
  3. 3.Plan the battery side before the first ride(Fit a fuse (the creator used 40 A) and use a 48 V pack rated for the controller's current; his lead-acid pack overheated after 10 minutes.)

KNOWN ISSUES

  • The $20 price is the alternator only. The controller, throttle, batteries and kart were extra, and the video does not price them.
  • Your alternator may have three, four or six sets of stator wires. With six, use the multimeter continuity check to find which two wires belong to each winding and label them before wiring the delta.
  • The controller must work with sensorless motors. The creator stresses that without that, the conversion will not run.
  • The test ended after 10 minutes with one lead-acid battery overheating and smelling burning. The controller can output up to 45 A while his pack was rated for 36 A over 7 minutes, so size the battery pack for the current, always fit a fuse (he used 40 A) and stop immediately if anything smells hot.
  • The video does not show how the motor is mounted on the kart or how it drives the wheels, so you will need to work out the mount and drive for your own kart.
  • Keep the brush assembly: solder a wire to each brush and supply 12 V to the rotor winding alongside the 48 V stator supply.

Can I use a different alternator?

Probably, but only a 4.6 L Ford F-150 alternator is shown. Check how many sets of wires come from the stator: three sets means it is already delta-connected, four means Y-connected, and six (as in the video) means you must find the ends of each winding with a multimeter and wire Y or delta yourself.

What voltage should I run?

The video runs the stator at 48 V from the kart's existing lead-acid pack, with 12 V on the rotor winding through the brushes. Other voltages were not tested.

Why did the battery smell after ten minutes?

The creator's lead-acid pack is rated for 36 A over 7 minutes and 24 A over 30 minutes, while his controller can output up to 45 A. He had a 40 A fuse installed, but concluded he most likely over-discharged the batteries, and one of them overheated and smelled burning. His takeaway was that he needs a more powerful battery pack.

How fast can this go?

The kart reached a top speed of 37 km/h in the video. Power and torque were not measured.

Community builds

No community builds yet — be the first, we feature the best ones.

Discussion1

FROM THE COMPAREE TEAM

The kart hit 37 km/h and ran ten minutes before the lead-acid pack over-discharged. What would you change first: move to lithium with a BMS, or keep lead-acid and add a low-voltage cutoff?

CompareeTEAM23d ago

Practical notes from our verification: the YouTube video is narrated and shows the diode pack removal, the multimeter check of the six stator wire pairs (01:01-02:25), the delta wiring and the test ride, but there is no written BOM, wiring diagram or controller model. The $20 is the alternator only; the controller, throttle, batteries and kart come on top and are not priced. Power was not measured. The 10-minute run ended with one lead-acid battery overheating and smelling burning, even with a 40 A fuse, so the battery pack is the part to get right. If you already work with 48 V packs and brushless controllers, this is a cheap motor source to experiment with.

Austin Blake

Austin Blake is a YouTube maker who already had an electric go-kart. He picked an alternator from a 4.6 L Ford F-150 because it cost only $20 and was in fairly good condition, rewired it as a motor and drove the kart with it.

Star the project on GitHub

DISCLAIMER

  • Comparee is not the author of the projects featured here. All rights to each project belong to its creator — every page links to the original source, and we never host creators’ files.
  • Information is provided without warranty and may become outdated as projects evolve. Prices are indicative bands only — always check the creator’s parts list for current costs.
  • Building and operating any project is at your own responsibility. Protective equipment, safe workshop practice and compliance with local regulations are the builder’s responsibility.